Author Topic: Trions Stock Bots (Read 19024 times)

roboman2444 · « **Reply #100 on:** September 23, 2009, 03:13:42 PM »

ok for the drive motor extenders, get rid of them. move the baseplate anchors as close as you can to the edges of the bot, that should allow u to atach the motors
use the small wedges also for(i think) that they are better

you can probably use shiny wheels, but that will make it slightly slower.

TriTon · « **Reply #101 on:** September 23, 2009, 04:05:17 PM »

Quote from: roboman2444;68104

ok for the drive motor extenders, get rid of them. move the baseplate anchors as close as you can to the edges of the bot, that should allow u to atach the motors
use the small wedges also for(i think) that they are better

you can probably use shiny wheels, but that will make it slightly slower.

If the motors are on the inside, there will be no room for the batts. Shiny hubs wont even make the bot move.

Reier · « **Reply #102 on:** September 23, 2009, 04:07:00 PM »

Rotate the motors 90 degrees.

40757 · « **Reply #103 on:** September 23, 2009, 04:07:13 PM »

Put the drive in the chassis, stack the batts, raise the top spinner, widen the two side spinners, use rubbers, and small wedges.

roboman2444 · « **Reply #104 on:** September 23, 2009, 04:07:46 PM »

1. the base-plate extenders will be right against the edge, so the motors will be able to connect to them outside of the bot.
2. if u lower the base-plate extenders, it will be able to have shines.

TriTon · « **Reply #105 on:** September 26, 2009, 01:08:38 PM »

New VS

Reier · « **Reply #106 on:** September 26, 2009, 01:11:08 PM »

Interesting.

Naryar · « **Reply #107 on:** September 26, 2009, 01:15:14 PM »

Lighten that extender work please.

Clickbeetle · « **Reply #108 on:** September 26, 2009, 09:39:00 PM »

Inspired by Hell's Sawmill I see...

The chassis doesn't need to be that wide. You can put the battery on the other side of the Snapper and bring in the sides a bit more. Also, I'm sure you can use smaller wheels. With the extra weight gained I would put some armor over the front.

Nice skin too.

roboman2444 · « **Reply #109 on:** September 26, 2009, 09:51:58 PM »

wait how is the chassis like that?

TriTon · « **Reply #110 on:** September 27, 2009, 12:26:03 AM »

Quote from: roboman2444;68715

wait how is the chassis like that?

When making a wedge bot, move the points away from the bot instead of torwards.

This is an unfinished bot

Any ideas, suggestions?

Pwnator · « **Reply #111 on:** September 27, 2009, 12:47:19 AM »

Since it's a heavyweight, use DDTs instead of snapper2s since they pack a bigger punch. And try to curve the hammers so the extenders will be more protected.

TriTon · « **Reply #112 on:** September 27, 2009, 02:36:59 PM »

This is one of my older bots

I've got over 200 kg of weight left, any ideas.

roboman2444 · « **Reply #113 on:** September 27, 2009, 03:22:26 PM »

why do u have the serveos there? you can just axle load the tribars on.

somestrangeguy · « **Reply #114 on:** September 27, 2009, 04:44:58 PM »

Servo boosing maybe?

You could try axleload the servos so that you could attach more weapon motor on both of them, try to get 3 on each and upgrade drive to HPZ.

R1885 · « **Reply #115 on:** September 27, 2009, 05:45:16 PM »

Upgrade to HPzteks.
Irons Moar.

TriTon · « **Reply #116 on:** September 29, 2009, 09:32:27 PM »

Finally, after a month of editing, here is RMT 2!

Virus Bomb · « **Reply #117 on:** September 29, 2009, 09:36:21 PM »

How many razors?

TriTon · « **Reply #118 on:** September 29, 2009, 09:37:16 PM »

Quote from: Virus Bomb;69618

How many razors?

16, 4 on each DDT.

Sage · « **Reply #119 on:** September 29, 2009, 09:57:50 PM »

for the razors, dont use t connectors. use extenders.