This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Redalert
Pages: 1 ... 29 30 31 32 33 34 35 [36] 37 38 39 40 41 42 43 ... 68
701
« on: January 10, 2019, 03:22:40 PM »
Wow, 090901. That's really good. Now you know how dangerous they are.
702
« on: January 10, 2019, 03:21:01 PM »
it has too many batteries regardless of irl or dsl-s
wandering spinners need a lot of batteries to survive, especially the one I just built.
703
« on: January 10, 2019, 03:10:20 PM »
I sense a challenge.
Okay sure, my MW vs your wandering spinner
P.M me your bot, and the binding, please. Then, we'll fight them.
704
« on: January 10, 2019, 02:12:14 PM »
I sense a challenge.
705
« on: January 10, 2019, 01:23:54 PM »
Hey, Kix. Nice job. :)
706
« on: January 10, 2019, 01:21:44 PM »
Yes... Here's the tutorial. I. chassis adjusted as shown. II. It's up to you how high you adjust the tornado mag motor. Battlepack is up 2 notches, and the small drive motor (I forgot the name of the motor) is up 1 notch. III. baseplate anchor up 1 notch. I used an aluminum square extender and titanium armor plate for front defense. IV. Wire it. Drive motor spins counterclockwise, and spinner rotates clockwise. V. DONE
708
« on: January 10, 2019, 12:37:18 PM »
You all underestimate wandering spinners. One of my WS killed a popup exactly like Seism 13 in a few seconds. That's how powerful they are.
...and 090901 changed the name of my showcase and combined it with the guide. I actually like the new name because it basically describes the core of what I do in Ironforge- wandering spinners.
clever 090901 :)))
709
« on: January 10, 2019, 12:00:02 PM »
710
« on: January 10, 2019, 10:15:04 AM »
Spinnerpro Quad. Requires 96 volts because motors are wired in series. Found only in bots with mass amounts of battery power. Spinnerpro right angle motor, designed for lightweights. Fast, but not powerful. Spinnerpro E.E.M. (Energy Efficient Motor) also known as ECO. It gets its name from its ability to work on little power, and its ability to operate heavy bots. It has long magnets and a long armature, which make it turn slowly, and allow it to rotate mechanisms with great effort. (rule of third-class levers.) E.E.M.s do not need a ground, and run on any voltage from 6 volts (very slow) to 24 volts (regular speed) E.E.M.s are marked in green. E.E.M. MAX gearbox with Aluminum worm gear. Designed to operate slow parts on a bot- 1-1000 ratio E.E.M. MAG gearbox. Nicknamed "the crusher," this steel gearbox can handle over 1000 pounds of force, and is ideal for clampers. It has a gear ratio of 1-10000 ( 1-1000, 1000- 10000) actual, fully-assembled gearbox on the right, gear configuration shown left.
711
« on: January 10, 2019, 09:29:38 AM »
Ran out of kb. So, double post. Here's a Spinnerpro brushless motor, rated for 12-24v. Spinnerpro motors have 3 terminals. > red- positive > black- negative > yellow- ground. Here's a custom 1-100 ratio gearbox. The shell's made of titanium, and the gears are made of hardened aluminum. included artios- 1-8, 8- 100(first- 1-8, second- 1-12.5: 100/8=12.5) Spinnerpro 18-36 v speed motor designed for spinners. has 2/3 the torque of the normal Spinnerpro motor, but 4/2 the speed. Marked in read to indicate that it's a speed motor. dual-speed gearbox designed for HS the main shaft is longer to prevent warping. Now, Micromotors are half the size of the original Spinnerpro 24v, and are the size of electric scooter motors. Micromotors run on 6-18 v.
712
« on: January 10, 2019, 09:22:40 AM »
Because It's a great foundation for building ideas.
713
« on: January 10, 2019, 08:12:08 AM »
building a WS with a cambered spinner.I. chassis as shown. set to minimum height. II. baseplate anchor for weapon raised up as high as possible. Control board attached on its side. Aluminum extenders added to stabilize bot. III. I used a 40 cm. Tribar and 10 kg. Sledgehammers. IV. DONE! if done correctly, you should have room for 10 mm. Titanium.
714
« on: January 10, 2019, 08:09:06 AM »
Okay, I was in a really, really big rush, so I threw this WS together in 2 minutes. 10 mm. aluminum
715
« on: January 10, 2019, 07:08:08 AM »
Drum spinner. 3d printable, and has working wheels and drum, allowing you to spin them by hand. here's the file...
716
« on: January 10, 2019, 06:14:08 AM »
melee is not a real smash game
how many years of research did it take to get to that conclusion?
I guess over a year to get that conclusion.
717
« on: January 10, 2019, 06:12:46 AM »
Okay! With all the help I’m getting, this will work out:)))
718
« on: January 10, 2019, 06:11:02 AM »
Finally, a good bot from you (No offense), but compared to others, THIS IS EPIC
Well, it’s hard to spend a lot of time on a bot when you’re rushed (ie- making an AI pack in just a few weeks.) Okay. How’s about more bots like it?
719
« on: January 10, 2019, 06:09:24 AM »
Wou have weight left over for drive.
720
« on: January 09, 2019, 03:00:04 PM »
Race the bots like you do cars.
Pages: 1 ... 29 30 31 32 33 34 35 [36] 37 38 39 40 41 42 43 ... 68
|
Show Posts
