Author Topic: plazmic infernos dsl showcase (Read 65198 times)

Tweedy · « **Reply #100 on:** April 02, 2012, 08:58:31 PM »

thanks

MassimoV · « **Reply #101 on:** April 02, 2012, 09:01:18 PM »

Hmmmm...is it possible to attatch the E-teks directly to the alu extender?

Tweedy · « **Reply #102 on:** April 02, 2012, 09:16:11 PM »

just tried it and unfortunately i can't attach them to the alu extenders
edit: this is probably also going to be my entry for the next dsl hw tourney that pops up

madman3 · « **Reply #103 on:** April 03, 2012, 03:55:42 AM »

Quote from: plazmic inferno on April 02, 2012, 09:16:11 PM

just tried it and unfortunately i can't attach them to the alu extenders
edit: this is probably also going to be my entry for the next dsl hw tourney that pops up

Trinity spinners are technically unrealistic so you'd have to wait for a DSL unrealistic tournament like Steel Warzone.

Jonzu95 · « **Reply #104 on:** April 03, 2012, 04:05:41 AM »

Plastic Extenders... not good... I recommend to use atleast aluminum extenders.

Hercules · « **Reply #105 on:** April 03, 2012, 02:49:24 PM »

Quote from: Jonzu95 on April 03, 2012, 04:05:41 AM

Polycarbonate Extenders... not good... I recommend to use atleast aluminum extenders.

Fixed

smashysmashy · « **Reply #106 on:** April 03, 2012, 06:26:16 PM »

Technically, I think polycarbonate is actually plastic. So you're both right. I like the bot, by the way.

Tweedy · « **Reply #107 on:** April 03, 2012, 06:28:22 PM »

thanks, the extenders never get hit so their fine as polycarb ones

Tweedy · « **Reply #108 on:** April 06, 2012, 10:12:57 AM »

DP
made a new vs, smoke on the water:

steel 5 armour, techno's on npc regulars, 5 ant batteries, 2 60kg hammers on a 20x200 dsl bar powered by a dual perm

MassimoV · « **Reply #109 on:** April 06, 2012, 01:11:45 PM »

The wheel extenders seem vunerable. I don't think you need them that far apart. It would turn just the same if thew were closer to the body.

Tweedy · « **Reply #110 on:** April 06, 2012, 01:31:57 PM »

just shortened the extenders andthat left enough weight to upgrade the armour to steel10:

MassimoV · « **Reply #111 on:** April 06, 2012, 01:48:56 PM »

You need to find some weigh of attatching the weaponextender without using a baseplate because they take up way too much room.

Jonzu95 · « **Reply #112 on:** April 06, 2012, 02:17:24 PM »

>Steel 10

powerrave · « **Reply #113 on:** April 06, 2012, 02:21:36 PM »

What Jonzu is trying to say is that Steel 10 is overkill. Downgrade armour and maybe use the weight for more/better weapons or more external chassis protection.

Tweedy · « **Reply #114 on:** April 06, 2012, 02:22:46 PM »

i'll make those changes tomorrow as i'm working on my me3 website atm

Tweedy · « **Reply #115 on:** April 06, 2012, 03:22:17 PM »

DP
had a break from my website and changed the baseplate anchor for a multi extender setup, downgraded to ti10 and swapped the 60kg hammers for 70kg ones:

Naryar · « **Reply #116 on:** April 06, 2012, 03:24:38 PM »

UNREALISTIC BLAARGH

You can do better on extender work as well. Try putting the two halfsheets into a X shape, and attach motors and stabilizers directly to them. Maybe another extender so the motors's axles are parallel.

Tweedy · « **Reply #117 on:** April 14, 2012, 12:44:46 PM »

did the halfsheets in an X shape and attached everything to them, ti10 armour, quite stable, speed is OK, npc drive with vlads, the rest you can see

ty4er · « **Reply #118 on:** April 14, 2012, 12:50:40 PM »

put the batteries ontop of each other at the front of the chassis and put the npc's in the chassis and then get better wheels

and downgrade the armour to plastic 5

Enigm@ · « **Reply #119 on:** April 14, 2012, 12:51:28 PM »

What weapon motor does it use ?