Author Topic: HELP. (Read 2272 times)

infiniteinertia · « **on:** November 11, 2008, 05:35:58 PM »

My halfsheets dont work...they dont attach. always showing up as red. Any ideas...?

Urjak · « **Reply #1 on:** November 11, 2008, 05:38:50 PM »

Attaching them anywhere, or only to the baseplate?

infiniteinertia · « **Reply #2 on:** November 11, 2008, 05:48:36 PM »

Only to the baseplate.

Madiaba · « **Reply #3 on:** November 11, 2008, 05:48:43 PM »

Inf, the collision meshes of some components actually stick below the chassis. So check this by just removing some already installed components.

Flying_Chao · « **Reply #4 on:** November 11, 2008, 05:50:55 PM »

Also, make sure you're using the correct attachment point.

Naryar · « **Reply #5 on:** November 11, 2008, 05:52:36 PM »

Inf did you find the special AP? in the middle of the halfsheet, there are 2 AP's, one used for attaching to the baseplate.

and for some unknown reason you can't put it under an angled top plate or under very small baseplates.

Madiaba · « **Reply #6 on:** November 11, 2008, 06:01:53 PM »

Huh, I assumed Inf. knew that...

Sage · « **Reply #7 on:** November 11, 2008, 06:12:59 PM »

talking to him, he said he tried it with an empty chassis.

Madiaba · « **Reply #8 on:** November 11, 2008, 06:26:59 PM »

That's weird, but I know that there are irregularities in the chassis too.

Somebody · « **Reply #9 on:** November 11, 2008, 06:40:20 PM »

There should be another point on the big titanium sheet to attach it to the baseplate.

infiniteinertia · « **Reply #10 on:** November 11, 2008, 07:21:44 PM »

To some of you: I am not that dumb, I know how to attach components.

Madiaba: Ive tried it with various empty chassis before, and it didnt work on any.

Somebody · « **Reply #11 on:** November 11, 2008, 07:44:48 PM »

It hasn't been working on mine (most of the time) either.

infiniteinertia · « **Reply #12 on:** November 12, 2008, 04:32:36 PM »

Well its not working at all.

infiniteinertia · « **Reply #13 on:** November 13, 2008, 04:39:32 PM »

Am I mistaken? is this not technical support?

ACAMS · « **Reply #14 on:** November 13, 2008, 04:57:28 PM »

I don't think titanium sheets, or half sheets are designed to attach to the base plate.

Madiaba · « **Reply #15 on:** November 13, 2008, 05:30:11 PM »

Inf, send me both your bot and the gmf of the half-sheet and I'll look it over.

infiniteinertia · « **Reply #16 on:** November 13, 2008, 06:13:13 PM »

Quote from: ACAMS;21527

I don't think titanium sheets, or half sheets are designed to attach to the base plate.

Halfsheets clearly are.

Madiaba; I will send you my .gmf, because the problem is universal.

70 CUDA · « **Reply #17 on:** November 14, 2008, 02:30:45 PM »

ya i have this problem off and on depending on day. i have no clue what caused it.

Clickbeetle · « **Reply #18 on:** November 22, 2008, 11:10:53 PM »

Is the error you're getting at the bottom of the screen, "Baseplate components must fit inside the chassis"?

I hate that error. I don't know how to bypass it. It happens if you try to attach a baseplate component on a chassis that's too flat (like at the front of a wedge, or else just on a really flat box).

You should be able to attach half sheets to a tall box.

Pwnator · « **Reply #19 on:** May 30, 2009, 01:16:40 AM »

Sorry for the big bump, but I just tried this and it worked.

I adjusted the height such that I was able to put a battlepack vertically. I was then able to put a half-sheet under. But when I slided the chassis down by even just one pixel, I can't attach the half-sheet (nor a vertical battlepack).

Not sure if this works for you guys, though.