Author Topic: Pip's DSL Stuff (Read 142821 times)

MassimoV · « **Reply #200 on:** December 26, 2011, 02:33:08 PM »

For the BW, you can make the chassis smaller.

ty4er · « **Reply #201 on:** December 28, 2011, 04:19:27 AM »

shrink the chassis and angle some of the extenders downwards perhaps.

Philippa · « **Reply #202 on:** December 31, 2011, 05:47:05 PM »

This any better?

NFX · « **Reply #203 on:** December 31, 2011, 05:54:04 PM »

Weapon rack needs to be straightened up. And preferably raised up one notch, to help when it's inverted, and to offer better protection against spinners. Apart from that it doesn't seem too bad. If you want to rotate some of the extenders so the razors point upwards/downwards, that would also help.

freeziez · « **Reply #204 on:** December 31, 2011, 06:00:02 PM »

From the looks of it, the drive motors are a little off. If it helps straighten driving, then try evening them out.

Philippa · « **Reply #205 on:** January 01, 2012, 07:30:13 AM »

[quote authour=NFX]If you want to rotate some of the extenders so the razors point upwards/downwards, that would also help.[/quote]
What would be better? All the same way or one up, one down, one up etc...

NFX · « **Reply #206 on:** January 01, 2012, 07:38:47 AM »

Ideally, some of them should be pointing up, and some should be pointing down. If you take a look at Urjak's recent version of Enturon, that's a pretty good way of doing it.

ty4er · « **Reply #207 on:** January 01, 2012, 07:43:11 AM »

keep the multi the same height it is and angle the end poly's upwards. and straighten it out.

And what's the weight/armour?

Philippa · « **Reply #208 on:** January 01, 2012, 12:23:15 PM »

Ty - Weight, is 174.something and plastic something too. Will get around to checking and modifying it.

In the meantime, made an IRL axebot. Fails and havoks frequently. Only really posting it to kill time for the Hedgehog. Um, 6 ants, no idea on armour and is called Badly Behaved Woodpecker.

MassimoV · « **Reply #209 on:** January 01, 2012, 01:49:36 PM »

For some reason I like it. Something that would be seen in series 1 or 2 of RW.

Philippa · « **Reply #210 on:** January 06, 2012, 07:06:58 AM »

Overpowered shell spinner Rainbow Turtle.

Help welcome.

That Robot is a Spy! · « **Reply #211 on:** January 06, 2012, 08:05:19 AM »

Change the razors to one every two panels.
So Razor>Blank>Razor>Blank>Razor>Blank>Razor>Blank
Also, change the control board, you have enough room for the lighter one.

Naryar · « **Reply #212 on:** January 06, 2012, 11:05:57 AM »

What TRIAS said, and be sure to remove the razors as well. Also, use a 80cm sheet for stabilizer.

Philippa · « **Reply #213 on:** January 06, 2012, 12:44:49 PM »

Quote from: That Robot is a Spy! on January 06, 2012, 08:05:19 AM

Change the razors to one every two panels.

Put the razors on flails or just on the shell?

Quote from: Naryar on January 06, 2012, 11:05:57 AM

Also, use a 80cm sheet for stabilizer.

On the shell or on the chassis?

Naryar · « **Reply #214 on:** January 06, 2012, 12:47:44 PM »

You don't have enough weight for flails.

ty4er · « **Reply #215 on:** January 06, 2012, 01:26:23 PM »

OR

you could make it a hs and angle the whole chassis down so the weapon is closer to the floor. That's only if you want, you could finish this one and make that if you want.

otherwise do what they said :P
and swap the extender for a sheet

Philippa · « **Reply #216 on:** January 06, 2012, 02:16:14 PM »

Like this?

Naryar · « **Reply #217 on:** January 06, 2012, 02:19:23 PM »

Yeah, that's it.

It's pretty decent anyways.

Philippa · « **Reply #218 on:** January 07, 2012, 08:25:22 AM »

New artbot. Just need to skin the chassis and components and should be done.

Can you tell what it is yet? [/RolfHarris]

GoldenFox93 · « **Reply #219 on:** January 07, 2012, 08:26:31 AM »

Quote from: Kurt Wylde on January 07, 2012, 08:25:22 AM

Can you tell what it is yet? [/RolfHarris]

A Reindeer?