Author Topic: GF93's DSL Scrapyard (Read 38642 times)

GoldenFox93 · « **Reply #100 on:** July 13, 2011, 02:48:40 PM »

Here, I have the prototype for my BB2 entry-

I haven't painted it yet, but it's a combined lifter/crusher robot, that can either use its front claws and wedges to push and flick opponents around, or chomp down on them. Comments?

Conraaa · « **Reply #101 on:** July 13, 2011, 02:50:43 PM »

That does look very nice. What armour?

GoldenFox93 · « **Reply #102 on:** July 13, 2011, 02:51:28 PM »

Plastic 3, sadly. Had to compromise to get everything I needed in.

NFX · « **Reply #103 on:** July 13, 2011, 02:58:30 PM »

Doesn't look too bad, I reckon. Nice work. What sort of drive motors are you using?

GoldenFox93 · « **Reply #104 on:** July 13, 2011, 03:03:57 PM »

Quote from: NFX on July 13, 2011, 02:58:30 PM

Doesn't look too bad, I reckon. Nice work. What sort of drive motors are you using?

Four of those black and silver ones which look a bit like RADs.

NFX · « **Reply #105 on:** July 13, 2011, 03:06:07 PM »

TWMR3's? That's what Freezerburn used, so it should be reasonably nippy. Not bad. Is it invertible in any way, though?

GoldenFox93 · « **Reply #106 on:** July 13, 2011, 03:10:58 PM »

Yes- it can run upside-down quite well.

SteveM4 · « **Reply #107 on:** July 13, 2011, 03:17:44 PM »

Does it have a tendency to sit on its side when flipped though?

GoldenFox93 · « **Reply #108 on:** July 13, 2011, 03:19:20 PM »

Haven't seen it happen myself, but it might be a concern. I've tested it against both lifters and flippers though, so it's mostly just been either upside-down or downside-up most of the time.

SteveM4 · « **Reply #109 on:** July 13, 2011, 03:21:35 PM »

>>GF52

Yes, but have you been up against an underpowered Beta flipper?

GoldenFox93 · « **Reply #110 on:** July 13, 2011, 03:23:30 PM »

Watch it, mate XD

Anyway, not yet, though. They mostly tend to get their flippers stuck up, though.

SteveM4 · « **Reply #111 on:** July 13, 2011, 03:34:55 PM »

>>GF38
Have you seen mine?
(Flipper comes back down)

Pwnator · « **Reply #112 on:** July 14, 2011, 03:02:29 AM »

SKIN IT

GO GO GO

GoldenFox93 · « **Reply #113 on:** August 06, 2011, 01:57:08 PM »

My first prototype entry for Blades of Fury-

Hopefully I won't get banned for the name.
Anyway, it's got 3mm Steel Armour and 30kg rotary hammers, powered by a Perm 80- great for bringing the hurt unto IRL MWs. My main concern is that it could be faster, with only rubbers driven by slimbodies pushing all that weight around. Any suggestions on how?

Naryar · « **Reply #114 on:** August 06, 2011, 01:58:01 PM »

So unrealistic

GoldenFox93 · « **Reply #115 on:** August 06, 2011, 01:58:49 PM »

Quote from: Naryar on August 06, 2011, 01:58:01 PM

So unrealistic

Well, it is a prototype. What are your recommendations?

Somebody · « **Reply #116 on:** August 06, 2011, 01:59:11 PM »

Get a longer Perm and it will look cooler. Use the weight anyway you can.

IIRC Slimbodies are 25, and TWM3R Drive Motors are 30, so you could use the weight that way and get some pretty good drive.

ty4er · « **Reply #117 on:** August 06, 2011, 02:00:30 PM »

Make it have a disk instead of a bar if you really have to.

Looks rather cool though, perhaps lower the armour a bit and get vlad wheels on?

Naryar · « **Reply #118 on:** August 06, 2011, 02:03:22 PM »

I would just use two DSL bars on multi's rather than that heavy extender work you have here to supposely hold the motor's axle.

Badnik96 · « **Reply #119 on:** August 06, 2011, 02:06:02 PM »

cool.

Unrealistic however, get a longer Perm.

Give it Vlads and TWM3R drive, then replace the 3MM steel with either Plastic 5 or Tite 3 and then send it to me :P