Author Topic: Ayak420 Showcase Need Help (Read 20158 times)

NFX · « **Reply #120 on:** November 06, 2011, 07:09:41 PM »

It has a few spinning weapons, rather than lots, which wouldn't deal much damage at all IRL. Although IRL Building + Metal Hinge wedges = Poor show. Remove the Metal Hinges and Side Panels, and I reckon that'd allow you to get a skirt hinge with some stronger protection on the front, such as Titanium 40cm Panels. I might put a Hazard-esque spinning blade, or a tribar of some description with a few weapons on it, rather than the Frenzy hammer assembly you have at the moment, for added IRL-ness.

ayak420 · « **Reply #121 on:** November 07, 2011, 09:13:29 PM »

Kept the metal hinges only because the wedge would not work otherwise.

MassimoV · « **Reply #122 on:** November 07, 2011, 09:21:48 PM »

If it's IRL, I like it.

ayak420 · « **Reply #123 on:** November 07, 2011, 09:41:09 PM »

Ya it is an IRL bot.

Also is there an AI pack that has a bunch of IRL bots to fight against?

MassimoV · « **Reply #124 on:** November 07, 2011, 09:43:07 PM »

There is an IRL pack which has a bunch of custom components. The bots are kind of mediocre and the project fell apart due to lack of interest.

FOTEPX · « **Reply #125 on:** November 08, 2011, 09:41:04 AM »

Quote from: ayak420 on November 07, 2011, 09:13:29 PM

(Image removed from quote.)

Kept the metal hinges only because the wedge would not work otherwise.

That's about as IRL as a block of cheese.

And blocks of cheese are IRL so

NFX · « **Reply #126 on:** November 08, 2011, 10:06:09 AM »

Doesn't look too bad. I might try having the disc further back, and a wheel at each corner. That'd probably help with the wedge a little bit, as well as with stability and turning circle. As I've said, though, IRL Building + Metal Hinge Wedges = Poor show. You could probably attempt a skirt hinge, I think that should work reasonably well for IRL building, but you don't see wedges like Metal Hinge ones on real bots for offense. Only for defense on the sides, such as Panic Attack. If it was on the front, it would dig into the ground, and screw up your mobility.

ayak420 · « **Reply #127 on:** December 02, 2011, 12:27:29 PM »

Armor: 10mm Steel

Two Judge motors for the flipper and 7 or 8 batteries.

smashysmashy · « **Reply #128 on:** December 02, 2011, 12:34:38 PM »

If this is IRL then:

Metal hinge wedges = poor show.

powerrave · « **Reply #129 on:** December 02, 2011, 12:42:13 PM »

This? IRL? Hell no. Exposed motors on the top is a more typical thing from DLS Realistic.

And on that note. Steel 10 is overkill. downgrade armour and get better wedges (DSL bar with small wedge).

NFX · « **Reply #130 on:** December 02, 2011, 12:56:33 PM »

Hammer/Flipper Hybrid? Don't see too many of those. I'd try to get the hammers potisioned closer to the center of the machine, though, rather than out at the sides. I'd also swap the Mags for BSG's, to save on weight and batteries. I'd drop the armour to Tite 5 at the very most, and add some more batteries to supply the bursts, I think you need at least 14 for this design if you used four BSG's.

ty4er · « **Reply #131 on:** December 02, 2011, 01:00:16 PM »

uh what mags, they're judge bursts :P
You would need more batterys though.

Naryar · « **Reply #132 on:** December 02, 2011, 01:02:52 PM »

it's not even dsl realistic since it uses gay judge bursts

NFX · « **Reply #133 on:** December 02, 2011, 01:03:46 PM »

If it's a serious DSL bot, then they should be BSG's. If it's IRL, then the motors shouldn't be exposed like that, and GET RID OF THOSE METAL HINGE WEDGES. Seriously, they really do turn my nuts the wrong way.

Still needs more batteries and less armour, though.

Naryar · « **Reply #134 on:** December 02, 2011, 01:30:25 PM »

In overall hammer/flippers just suck unless they are really good at clamping and are surrounded with stabilizers.

Quote from: NFX on December 02, 2011, 01:03:46 PM

If it's a serious DSL bot, then they should be BSG's. If it's IRL, then the motors shouldn't be exposed like that

=> you implying IRL isn't serious DSL. Thank you NFX.

Anyways, why are metal hinges so hated in IRL ? Because the mass has decided so, or is there a reason for it ? They're pretty much realistic, and snapper wedges (which are probably better than metal hinges) are not frowned upon.

NFX · « **Reply #135 on:** December 02, 2011, 01:45:03 PM »

Quote from: Naryar on December 02, 2011, 01:30:25 PM

Quote from: NFX on December 02, 2011, 01:03:46 PM
If it's a serious DSL bot, then they should be BSG's. If it's IRL, then the motors shouldn't be exposed like that

=> you implying IRL isn't serious DSL. Thank you NFX.

Anyways, why are metal hinges so hated in IRL ? Because the mass has decided so, or is there a reason for it ? They're pretty much realistic, and snapper wedges (which are probably better than metal hinges) are not frowned upon.

DSL and IRL are different building styles. Though the line is being blurred by some. IRL places aesthetics above efficiency, whereas with DSL, it's the other way around. Both are excellent, in my view, and both take different building aspects seriously. =D

And Metal Hinge - or sprung - wedges are only ever used in IRL for side defense. If you tried to use it on the front as an offensive strategy, it would simply dig into the ground, and severely hinder your mobility, probably folding under you sooner or later.

ayak420 · « **Reply #136 on:** December 04, 2011, 07:42:42 PM »

Armor 5MM Plastic

MassimoV · « **Reply #137 on:** December 04, 2011, 10:14:08 PM »

Why is the one tooth turned at a weird angle.

powerrave · « **Reply #138 on:** December 05, 2011, 04:26:15 AM »

I like it, but I think you can get a lighter stabilizer at the back and then get alu or even ti extenders for the weapons.

FOTEPX · « **Reply #139 on:** December 05, 2011, 04:45:36 AM »

I really like it. Reminds me of NFX's SWARM. Only needs 3 ants, though.