Preytor_4's stock showcase

[Vertigo]

Definitely needs a wedge. But 4WD, nope.

But the almighty Naryar says not to.
You dare defy the Almighty Naryar!?

Since when was Naryar a Stockpert?

[madman3]

Definitely needs a wedge. But 4WD, nope.

But the almighty Naryar says not to.
You dare defy the Almighty Naryar!?

Since when was Naryar a Stockpert?

You bring apocalypse upon us.

Ideally you don't really want the lip at the front, since that just reduces the damage from the hammers.

[J]

Definitely needs a wedge. But 4WD, nope.

But the almighty Naryar says not to.
You dare defy the Almighty Naryar!?

Since when was Naryar a Stockpert?

I honestly read that as "Since when was Naryar as Sock Puppet?"
.......Look, don't analyze it.

Preytor, you can get that bot to 4Wd, , you could even do 6WD.
*Assuming you have stacked blacks*

[Preytor_4]

Ima post a new bot.

I present



Ghidrah (insides)

[madman3]

The chassis looks a mile high, could be shrunk quite a bit.
Also, the wedges are too narrow, so I'd rebuild the chassis so the wedges are wider.

[NFX]

I would use the DDT's for the wedges, and the SnapperII's for the weaponry. That should make it wedgier. And the back end of the chassis should be shrunk so the HPZ's are right up beside the batteries.

[Preytor_4]

The chassis looks a mile high, could be shrunk quite a bit.
Also, the wedges are too narrow, so I'd rebuild the chassis so the wedges are wider.

It's just a notch over how high a chassis has to be to fit a ztek

[NFX]

A chassis only needs to be five clicks high to fit an HPZ.

[madman3]

The chassis looks a mile high, could be shrunk quite a bit.
Also, the wedges are too narrow, so I'd rebuild the chassis so the wedges are wider.

It's just a notch over how high a chassis has to be to fit a ztek

Maybe it's just the pic or my apparent blindness.

And Snapper II's, NFX? You probably mean Snapper 2s.

[NFX]

The chassis looks a mile high, could be shrunk quite a bit.
Also, the wedges are too narrow, so I'd rebuild the chassis so the wedges are wider.

It's just a notch over how high a chassis has to be to fit a ztek

Maybe it's just the pic or my apparent blindness.

And Snapper II's, NFX? You probably mean Snapper 2s.

Ordinarily, yes, but SnapperII's could work if there's not much weight on them.

[madman3]

The chassis looks a mile high, could be shrunk quite a bit.
Also, the wedges are too narrow, so I'd rebuild the chassis so the wedges are wider.

It's just a notch over how high a chassis has to be to fit a ztek

Maybe it's just the pic or my apparent blindness.

And Snapper II's, NFX? You probably mean Snapper 2s.

Ordinarily, yes, but SnapperII's could work if there's not much weight on them.

Yeah, but they'll have almost no impact force; it's like putting ten razors on a single DDT but worse.

[Preytor_4]

+1 Thread Resurrection

So, I got bored and decided to edit Rheum and this is what I got:

[madman3]

Well exostacked air canister.
How well does the poker section work against HS in practice?

[Preytor_4]

Well exostacked air canister.

2 stacked canisters (yay hax mode)

How well does the poker section work against HS in practice?

Haven't actually tested it, should probably go do that...

[Mr. AS]

yay hax mode

EW why would you use hax mode on a serious bot ? if you're gonna hax mode at least go all out on it

[ty4er]

place the piston further back

and i think you can do this without hax mode

[Naryar]

Needs moar air canisters, actually 2 larges.

[Fracture]

Needs moar air canisters, actually 2 larges.

For one piston?!

Please clean up the drive setup...it won't even move with the way you've rotated the HP Z-Teks right now. Try to get the bot symmetrical.