Author Topic: NFX.showcase/stock (Read 207244 times)

Pwnator · « **Reply #80 on:** May 05, 2010, 04:18:29 AM »

Is it just me or are the wedges uneven?

That aside, it's quite a cool looking popup. Good job. :D

Naryar · « **Reply #81 on:** May 05, 2010, 04:37:56 AM »

It is just you

NFX · « **Reply #82 on:** May 05, 2010, 10:31:40 AM »

No, he's right, the wedges and ramplates are slightly to one side, just because of the way the Snappers fit in between the DDTs.

NFX · « **Reply #83 on:** May 05, 2010, 12:34:32 PM »

More snapper loaded HS action here, this time a heavyweight (forgot the add the weight to the splash, it's 795.7). After a discussion about some HS's, not sure where, the topic of Sage's old 48-mace HS cropped up. He told me it wasn't terribly practical, so I decided to try and build a 48-razor HS. And it's worked! Not sure how well it'll do against the more accepted 36-mace HS's, though.

Sage · « **Reply #84 on:** May 05, 2010, 03:05:15 PM »

Hey, there you go. Nicely done.

I would appreciate if you could make your splashes a little larger. The way it is now you could make it your signature...

It's hard to see.

NFX · « **Reply #85 on:** May 05, 2010, 03:15:55 PM »

Thanks, Sage. I'll make my splashes bigger, it's just this one was so damn wide to begin with.

G.K. · « **Reply #86 on:** May 07, 2010, 03:34:44 PM »

Quote from: Naryar on May 01, 2010, 06:30:58 PM

NOT a spider, but an insect.

Reminds me of a classic top gear moment.

NFX · « **Reply #87 on:** May 10, 2010, 06:55:58 AM »

Just thought I'd showcase my entry for GK's BTTB tournament. 798.6 or thereabouts. 16 Irons, 2 Stacked BlackVolts, 3 DDT's for the flipper, 4 Z-Tek's for the weaponry, DSA. Outwedges Neglected Waterbug, and gutrips almost anything. Even HS's =P

Naryar · « **Reply #88 on:** May 10, 2010, 08:18:47 AM »

It should have tribars but thank you.

NFX · « **Reply #89 on:** May 10, 2010, 08:48:24 AM »

You're welcome. =) Let's hope it does well.

Pwnator · « **Reply #90 on:** May 13, 2010, 02:14:16 AM »

Say goodbye to my bot's chances. It'll just pull off a Rage III. XD

Anyway, does your bot have problems in steering? Usually 4 bursted VSes tend to tip over without wide enough side support.

NFX · « **Reply #91 on:** May 13, 2010, 08:23:17 AM »

It's fine when it's going forwards, somehow. It just tends to tip over a bit when it reverses and turns while the discs are going. Did get beached on its side a few times during testing, so I put the small extenders sticking out the sides, that seems to prevent that happening now.

G.K. · « **Reply #92 on:** May 13, 2010, 04:10:31 PM »

Don't see that happening Pwn.

NFX · « **Reply #93 on:** May 18, 2010, 09:39:58 AM »

I decided to have another try at snapper loading, and managed to get myself a one-snapper HS. Only downside, apart from the plastic armour and the low battery life, is that it does have a tendency to randomly drop a Havok Bomb on itself at any point during the match. But more often than not it's relatively smooth running.

Squirrel_Monkey · « **Reply #94 on:** May 18, 2010, 10:57:01 AM »

Blackvolt=Supervolt?

G.K. · « **Reply #95 on:** May 18, 2010, 11:01:54 AM »

Clickbeetle · « **Reply #96 on:** May 18, 2010, 03:40:20 PM »

That kind of reminds me of a MW Chernobyl. Nice job.

Also, when you look at it upside down, the name on top says HS.

NFX · « **Reply #97 on:** May 18, 2010, 05:17:01 PM »

Well spotted, Click. That's probably not something I would have initially picked up. =D

Pwnator · « **Reply #98 on:** May 18, 2010, 08:06:45 PM »

It's actually symmetrical! :O I would have never thought of a setup like that (that's because I usually check if it works on HWs). Nice. :D

Naryar · « **Reply #99 on:** May 19, 2010, 03:23:35 AM »

How is this symmetrical exactly ?