Author Topic: KOS' Incarnations (Read 51492 times)

KOS · « **on:** November 14, 2013, 05:15:15 PM »

Deathmill 17:

One of my favorite 36 maced spinners - DSA, 3 maces on each extender, 4 hpz's, protected wheels. Leave any feedback on the robot :D

Deathmill 16:

Another 36 maced spinner, this one is based off the legendary 36 maced spinner, absolute chaos, but has been completely remade : (Smaller chassis, better arranged mace placement, slightly more protected wheels) - DSA, 3 maces on each extender, 4 hpz's. Leave any feedback on the robot :D

Possibly my favorite vertical spinner - dsa, 16 irons, 4 hpz (2x2 chained), inside wheels, decent wedge, stable. Leave any feedback on the robot :D

Mr. AS · « **Reply #1 on:** November 14, 2013, 05:41:02 PM »

looks solidly build. not even just for a first bot either, just solid in general. the only problem i can really think of is the turning speed caused by the wheels being close together, but its fine.
they look similar to other designs (you probably looked at them while you were lurking), but its fine. not many people start out with a completely game-changing design when they start out. i'm sure it'll straighten itself out as this showcase goes on.

HurricaneAndrew · « **Reply #2 on:** November 14, 2013, 05:45:12 PM »

Whoa. You've been lurking.

KOS · « **Reply #3 on:** November 14, 2013, 05:55:49 PM »

Thanks for the feedback, i hope to learn a lot more and make some more uniquer designs. But hey gotta start out somewhere :D

Naryar · « **Reply #4 on:** November 15, 2013, 03:19:17 AM »

good starting designs, although stop getting wheels so close to each other - it diminishes turnspeed

NeighImACarrot · « **Reply #5 on:** November 23, 2013, 04:38:11 PM »

Noice robots, they're difficult to beat

KOS · « **Reply #6 on:** November 23, 2013, 04:48:06 PM »

Thank you

KOS · « **Reply #7 on:** December 07, 2013, 05:30:05 PM »

This is a new lightweight i just finished on. : DSA, 2 ztek's 6 razors, AND CAMBERED WHEELZ :D:D:D

Badnik96 · « **Reply #8 on:** December 07, 2013, 07:25:13 PM »

Not bad, but the BBEANS nifty is illegal for tournaments. :P

KOS · « **Reply #9 on:** December 08, 2013, 06:06:32 AM »

yea i'm going to try fitting a stock one. its just that it will take ages with the size of the chassis. :)

KOS · « **Reply #10 on:** December 08, 2013, 06:24:49 AM »

finally got a stock nifty to fit :)

KOS · « **Reply #11 on:** December 10, 2013, 05:49:20 PM »

My newest spinner and possibly my best, it has 39 maces on 4 hpz's and a 2 hpz's drive, it also has 2 (stacked) blacks. The only problem i have is the crappy plastic armour :L

MassimoV · « **Reply #12 on:** December 10, 2013, 06:52:53 PM »

dang...

Mr. AS · « **Reply #13 on:** December 10, 2013, 07:35:15 PM »

I would probably move the black up in between the two snappers. *MAYBE* you *MIGHT* be able to get DSA by doing that.

KOS · « **Reply #14 on:** December 11, 2013, 11:25:50 AM »

You are correct Mr. AwesumSauce, here it is, a 39 maced spinner with dsa

I have also made a version with plastic armour and 40 maces :D

Scrap Daddy · « **Reply #15 on:** December 11, 2013, 12:58:52 PM »

my first 36HS setup :')

KOS · « **Reply #16 on:** December 11, 2013, 02:03:34 PM »

:D awesome

J · « **Reply #17 on:** December 11, 2013, 11:00:10 PM »

Just out of curiosity, why do 19's wheels stick out like that?

KOS · « **Reply #18 on:** December 12, 2013, 02:25:00 AM »

They stick out because if i were to directly attach the motor to the snapper the wheels wouldn't touch the ground and it would cause immense havoking.

KOS · « **Reply #19 on:** December 13, 2013, 07:02:03 PM »

Just a quick video to show my 40 maced spinner VS Absolute Chaos :D