Author Topic: Kill343gs's Comeback Tour (Read 26648 times)

Enigm@ · « **Reply #180 on:** July 01, 2014, 01:05:31 AM »

gucci

kill343gs · « **Reply #181 on:** July 02, 2014, 11:02:39 PM »

Sage · « **Reply #182 on:** July 02, 2014, 11:08:23 PM »

that looks awesome

kill343gs · « **Reply #183 on:** July 02, 2014, 11:11:00 PM »

all built off one snapper so it isnt the most stable thing in the world but it gets the job done. also its not a hpz

Badnik96 · « **Reply #184 on:** July 03, 2014, 01:45:40 AM »

Doubting the plow, how does it do against wedges?

kill343gs · « **Reply #185 on:** July 03, 2014, 11:48:08 PM »

ballasts make wedges gr8 m8

Naryar · « **Reply #186 on:** July 04, 2014, 02:26:03 AM »

kill343gs · « **Reply #187 on:** June 23, 2015, 01:16:40 AM »

lol im so bad at this game.

weight is 70.08 and i need another black battery in there and im not rebuilding the chassis to redo the whole setup nonononono. The VS and FS are on RADs. HS are on regular Zteks. At least I didn't take the easy route and do Sage's wedged poker. Don't ever let anyone tell you I take the easy way out... FS VS HS hybrid...

ShaverBX

edit: also kinda sad because i factory reset my old laptop and i dont think i have any of those LWs now D:

Pwnator · « **Reply #188 on:** June 23, 2015, 01:23:36 AM »

You could probably swap the HS and VS motors around for better distribution of damage because a RAD VS setup hits like a wet noodle, but a RAD HS setup can still do some average damage.

Also is the weight 790.8 or 700.8? You could probably swap the irons for razors if you need another black.

kill343gs · « **Reply #189 on:** June 23, 2015, 01:28:17 AM »

the weight is 770.8. I need 30kgs. If I do end up shaving the chassis down I will switch the motors because I see your point

Naryar · « **Reply #190 on:** June 23, 2015, 01:42:12 AM »

Bot is very cool. Don't let the tediousness of stock stop you !

It does look a bit messy though. If you can clean that it would look even better.

is there a way to move the VS's forward, put the rads parallel to the axle and win 4kg or do the snappers bend sideways instead of forward

you can do it kill !

kill343gs · « **Reply #191 on:** June 23, 2015, 03:17:29 AM »

I forgot how excited I used to get to receive feedback and stuff. Here I am in bed at 4am and I just had to log onto my phone and come check.

Nary, the snappers thst hold the weapon racks are mounted via the back attatchment point so the VS rotate as opposed to lean. When I rebuild it tomorrow I will look I to changing it, although that will really just be for . looks as they actually reach fairly well

G.K. · « **Reply #192 on:** June 23, 2015, 03:59:20 AM »

As long as its wedges aren't horrible that's going to be a really vicious bot to face.

Wish I could offer more sage (:P) advice but Pwn and Nary have it covered. Just 2WD?

kill343gs · « **Reply #193 on:** June 23, 2015, 11:25:16 AM »

Just 2wd. I needed as much weight for as many weapon motors as possible.

Edit: also the wedges have absolutely no reason to not be good. They're on standalone snappers further back in the bot and on 140cm extenders. But I'm sure they'll find a reason to be terrible because I built it.

kill343gs · « **Reply #194 on:** June 23, 2015, 04:12:42 PM »

all redid

actually incredibly stable because of the way i wired all the motors, they're all spinning towards the center of the bot and the VS are spinning downwards so it sticks to the ground way better than it should

Mr. AS · « **Reply #195 on:** June 23, 2015, 04:46:46 PM »

Wedges are too thin. Entire thing's too thin. Make it wider, don't go overboard and make it too thin horizontally though.

Basically, the bigger it is, the more stable it should be.

Sage · « **Reply #196 on:** June 23, 2015, 11:42:26 PM »

Yesssssss.
I would probably move the wedge snappers to be on each side of the middle snappers. like AS said wider might be better on this bot. Also probably make the VS motors go downwards to like trap the bot on the FS and damage the top. youre not gonna pick anything up with rads anyway.

but wow so excited to see this bot rebuilt

kill343gs · « **Reply #197 on:** June 24, 2015, 12:48:39 AM »

Quote from: Sage on June 23, 2015, 11:42:26 PM

Yesssssss.
I would probably move the wedge snappers to be on each side of the middle snappers. like AS said wider might be better on this bot. Also probably make the VS motors go downwards to like trap the bot on the FS and damage the top. youre not gonna pick anything up with rads anyway.

but wow so excited to see this bot rebuilt

Quote

they're all spinning towards the center of the bot and the VS are spinning downwards

Naryar · « **Reply #198 on:** June 24, 2015, 01:39:05 AM »

i don't have that much experience with stock but it seems fine to me

kill343gs · « **Reply #199 on:** September 29, 2016, 10:51:58 AM »

My name is deadbeat and my chassis is too short for baseplate mounted HPZ drive.

I think it's 3 black batteries, but it might have been 2. This took too many rebuilds so I can't remember.