This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Tweedy
Pages: 1 ... 32 33 34 35 36 37 38 [39] 40 41 42 43 44 45 46 ... 74
761
« on: August 20, 2012, 12:29:59 PM »
I'll join as well if you guys want to make it a 4-way rumble ?
762
« on: August 19, 2012, 08:22:30 PM »
If that was a lightweight IRL you could totally pull off putting the receiver, speed controls, batteries etc. inside of the chassis. The CB exostacking is fine, no 'bot electronics are that big IRL.
4QD speed controllers And this is not IRL, the stress on the motors alone would make the axles on the motor break and you souldn't be able to attach the motors on extenders that way securely
763
« on: August 19, 2012, 09:12:18 AM »
My top 10 in no particular order:
The cabin in the woods
Alien
The hangover
Pee Wee's big adventure
Hot Fuzz
Juan of the dead
Dawn of the dead
Evil dead
Talladega Knights: The Ballad Of Ricky Bobby
Step Brothers
764
« on: August 17, 2012, 04:03:23 AM »
I built a bot almost exactly the same as this a few days ago but didn't showcase it
765
« on: August 17, 2012, 03:59:07 AM »
try going into decimals such as math.py*1.5
766
« on: August 16, 2012, 04:12:19 PM »
i'd also reskin the disc red and black
767
« on: August 16, 2012, 02:06:16 PM »
bump
@Click
with you deleting the metal hinge and making the skirts useless for wedges in DSL 3, what can we use to attach our wedges with?
My guess is that chassis wedges will become more popular or there will be a new component to make wedges.
768
« on: August 16, 2012, 05:06:15 AM »
The IRL bot looks better but the small wedges attached to flipper segments makes it look unrealistic, try attaching flipper segments to the bottom of the flipper arms to act as wedges and if you're using judge bursts then use 12 ants rather than 2 ants and 2 battle packs
769
« on: August 16, 2012, 03:40:25 AM »
770
« on: August 15, 2012, 10:10:19 AM »
Little demonstration of an actually IRL and simple flipper for Gauche.
(Image removed from quote.)
Bit of a more American style one. To make it even more IRL, the gap in the chassis would be thinner.
4 wheel mag (with wide ants at the front and plain ants at the back) drive, judge burst for the flipper, 5 ants, 2 battlepacks.
Also I needed to out Cryptopsy bot Enigma after he made Gravager (A Cryptopsy) haha
This looks pretty good, I think the bottom flipper segment could have one more attached to each side though ( that is, if you're going to improve it )
771
« on: August 15, 2012, 09:45:26 AM »
Piglet is also a clone of my MW Illusion of death
772
« on: August 15, 2012, 09:03:46 AM »
And also on ra2 metal hinges are ridiculously more effective than they are IRL
773
« on: August 15, 2012, 08:25:02 AM »
Just minimize concave spaces.
This. You want the bot to look like it is all one piece
774
« on: August 15, 2012, 06:21:58 AM »
Post a picture of it from the bot lab because from here it doesn't look IRL
775
« on: August 14, 2012, 12:29:09 PM »
What drive does it have and i'm guessing that's a mag snapper for the weapon motor ?
776
« on: August 14, 2012, 11:32:11 AM »
I really like the 2nd bot, can it self right though ?
777
« on: August 14, 2012, 11:26:06 AM »
That looks better, you still only need to use 12 ants for this IIRC
778
« on: August 14, 2012, 09:30:54 AM »
Gauche the flipper power?ITS TWO FREAKING JUDGE BURSTS, WHAT MORE DO YOU WANT?Seriously the flipper position sure wont matter when its that powerfull anyways
Gauche is right, if you place the judge bursts higher up and have the first flipper segment attached to it as the top of the flipper. And he's building a cruiserweight Massimo
779
« on: August 14, 2012, 09:05:34 AM »
If the beater bar plate stops bots from climbing the wedge then yes and the metal hinge should be removed either way which should give you a cruiser weight with weight left over for more armour.
780
« on: August 14, 2012, 07:27:22 AM »
In IRL you shouldn't use metal hinge wedges, you only need to use ant batteries for the judge bursts ( not sure how many ) and doesn't the plate with beater bars in the middle stop bots from going up the wedges ?
Pages: 1 ... 32 33 34 35 36 37 38 [39] 40 41 42 43 44 45 46 ... 74
|
Show Posts