This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Pwnator
6101
« on: September 26, 2009, 11:19:53 AM »
Like Reier said, downgrade to 5mm tite and add side protection and stronger wedges.
6102
« on: September 26, 2009, 08:59:02 AM »
Using a single component with a higher HP and fracture might be better. :D
6103
« on: September 26, 2009, 07:41:01 AM »
Well, you almost got the space management thing down, so it's a bit ok.
However, you shouldn't use pinks unless on subweight bots (or bots that barely require power). A single supervolt would power it enough for 3 minutes. And saws also suck in stock (basically, weapons 14kg or less are the only ones that are combat-worthy). And your wedge would do much better if it's a small wedge (an EMERGENCY wedge would work too, but not as good as the small wedge) and if it's on a snapper burst motor. A wide stance will also help your bot a lot so it wouldn't be prone to tipping over while steering.
And yeah, DK covered the rest. XD
6104
« on: September 26, 2009, 04:36:04 AM »
There's no harm in reposting it.
6105
« on: September 25, 2009, 10:32:49 PM »
Couldn't resist. 
6106
« on: September 25, 2009, 10:24:47 PM »
I'd photoshop in Pedobear just peeking behind the window if I had the time. XD
6107
« on: September 24, 2009, 09:07:19 AM »
You have to keep track of them. :D
6108
« on: September 24, 2009, 08:15:16 AM »
Yay. Trap bots = <3 :D
I'm guessing the perm spins downwards. But one of the main problems I had with Jigsaw was that the servo flexes wildly when it takes/makes a hard hit. Does this happen to yours?
6109
« on: September 23, 2009, 04:33:26 AM »
Longcat strikes again!  Hmmm... smoking does have its advantages... 
6110
« on: September 23, 2009, 04:03:42 AM »
A box chassis will be better on that one. :D
6111
« on: September 22, 2009, 09:12:57 AM »
Sorry, JB. Due to time constraints (and my RA2 keeps crashing as well), I'm dropping out on this one. But I'll still showcase the prototype when I have the time. :D
6112
« on: September 22, 2009, 05:12:48 AM »
^^^ 
6113
« on: September 22, 2009, 03:23:03 AM »
Hmm... if it's too slow, try to fiddle around to get Drive-Eteks on that. If possible, test if 2 JXes are better than 4 mags or not. :D
6114
« on: September 22, 2009, 03:14:29 AM »
Will it fare better against HSes when you replace the ramplate with a plow? :D
6115
« on: September 22, 2009, 03:12:54 AM »
@ S32: I dunno. I build one when I'm inspired by any bot I stumble upon when scouring through the pages.
@ 40757: Yep, I knew that. Just wanted to make a cool looking bot. I could've done better if I spent more time on it, though.
@ Reier: That was unintentional. I was playing with setups when I realized that the wheels arranged that way look awesome. XD
Impulse 5 is being refined to be a tough undercutter, but it loses its plow too easily. I'll fix it again when I'm done with my homework. :D
6116
« on: September 21, 2009, 08:34:04 AM »
6117
« on: September 21, 2009, 06:20:49 AM »
Firebeetle doesn't post much, but when he does it's always awesome. Fixed.
6118
« on: September 21, 2009, 06:11:29 AM »
I didn't AAM anything. If I did I would've also AAM'ed the snappers horizontally so it can be stable. :P
6119
« on: September 21, 2009, 03:32:41 AM »
Heh. GM2 couldn't beat half of NAR AI shell spinners (primarily because of the insane KE from the hammers, though it would fare better against the ones with irons and razors). But if CCIV is going to be HW, I assure you that I wouldn't enter a VS this time. :P
6120
« on: September 21, 2009, 03:05:08 AM »
PB: Thanks. :D
Nary: I had about 1-2kg left on Jackhammer when I used 1mm tite so I used steel instead. And sometimes GM2's speed is also its weakness. Its speed combined with SnSnSnSnS's power would fling both bots OOTA in the Electric Arena 2 (though sometimes SnSnSnSnS would stay in the arena). XD
|
Show Posts