This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Scorpion
Pages: 1 ... 22 23 24 25 26 27 28 [29] 30 31 32 33 34 35 36 ... 231
561
« on: August 15, 2011, 07:43:02 AM »
Titanium half sheet for bottom protection. The use the side AP's of that half sheet to attatch the stabilizers and drive to.
Personally, I think you can get by alright with aluminium stabilizers rather than titanium ones for LWs
562
« on: August 15, 2011, 06:41:34 AM »
Nope, apparently Lemon in slovakian translates to: citrón, citrónovník, citrónový: citrónová farba or haraburda Then again, that's just from an online free translator, so, yeah, probably not that accurate anyway...
563
« on: August 15, 2011, 06:21:02 AM »
And wait, 4 blacks? I'm hoping that's a typo..... You only need 2 Blacks for this bot. Nope. You need 3.
From the how power consumption works topic: For a typical HW popup with 4 HP Z-tek drive and 4 DDT's, you need 100 (x4) + 312.5 (x4) = 1650 total BEMIOR, which is about 2 Supervolts. Remember that these are minimum values, however, and your motors may start slowing down depending on how much total power you have.
This has 2 DDTs right? So 2 supervolts should be all you need.
564
« on: August 15, 2011, 05:06:51 AM »
IT PLEAZHEZ MEH
I like it a lot.
This lol
565
« on: August 15, 2011, 04:55:34 AM »
You have more than 10 KG to play around with there, i'd consider extending the wedges for one.
And wait, 4 blacks? I'm hoping that's a typo..... You only need 2 Blacks for this bot.
566
« on: August 15, 2011, 04:49:30 AM »
Yeah it spins up, sadly though irons scrape the floor, so I can't use them
How badly? You can always raise the snappers.
Thing is, raise the snappers here, you're also raising the drive and the stabilizers which cancels that out really.
567
« on: August 14, 2011, 04:01:07 PM »
Yeah it spins up, sadly though irons scrape the floor, so I can't use them
568
« on: August 14, 2011, 03:24:59 PM »
Hmmmmm, prehaps I should book a one way trip to Switzerland for my bot...
569
« on: August 14, 2011, 03:21:28 PM »
Backdraft:   DSA, 1 nifty, 3 casters
570
« on: August 14, 2011, 03:16:17 PM »
9 years old you say...
In which case Goose has posted 11000 times on here since he was born!
571
« on: August 13, 2011, 06:29:21 PM »
Thank you for this
572
« on: August 13, 2011, 06:23:12 PM »
Yup. Good thing I am bulletproof.
Good thing I have no physical form. =D
Good thing I AM that bullet
573
« on: August 13, 2011, 04:39:16 AM »
Yays, a vote :D
Seriously though, RPJK shouldn't even have one
Excuse me but I was going to vote for until I realised how much rep you gave people and you changed my rep the most.
So what? Come on, you can't honestly be saying you're as good a builder as ACAMS, and better than people like vertigo and 090901 (who just won wedge war with a great bot, and still gets no votes lol).
574
« on: August 12, 2011, 08:11:51 PM »
Yes, and like my mum, it needs to be longer ;P
575
« on: August 12, 2011, 08:06:39 PM »
It looks far too weak to being flanked ;P
576
« on: August 12, 2011, 08:02:02 PM »
Huh, yes it does? If not, where on earth did I get the 140 red extenders in all my stock games???
577
« on: August 12, 2011, 07:58:41 PM »
lol, well done ;P I know the wedges stick out too much as well, the problem is that i'm running out of chassis points to move them further back. I tried both wedges on 140's and wedges on 2 20 cm extenders, and the 140s performed best, so i've just stuck with them.
578
« on: August 12, 2011, 05:50:03 PM »
I'd try segmenting the wedges (even if just partially) and try putting the snowplow further down. I can see that helping trapping, and also, could help the wedges.
579
« on: August 12, 2011, 05:46:48 PM »
I only put in people who'd have even a chance of getting a vote for them.
AND who've been posting bots relatively recently.
580
« on: August 12, 2011, 04:44:22 PM »
lol, I don't even know who's up there nowadays
That's how much attention I give to DSL XD
Didn't you hear? I'm now the bestest ever, I am so good now i make IRL designs that can beat all the HWs in Nar AI. ;P But nah, and, oftopic slightly, but I'd love to see you build more in DSL (although, you're better IMO at stock).
Pages: 1 ... 22 23 24 25 26 27 28 [29] 30 31 32 33 34 35 36 ... 231
|