This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - NFX
5121
« on: August 04, 2011, 06:24:12 AM »
Metallica - One
5122
« on: August 03, 2011, 04:43:07 PM »
Not too bad. Strictly speaking, it needs 2 Blackvolts, though.
5123
« on: August 03, 2011, 04:25:07 PM »
floated down the delaware river all day on an inner tube.
now tacos yessss
The only thing better than a taco is 2 tacos.
5124
« on: August 03, 2011, 03:48:58 PM »
Use 90 Degree Baseplate Anchors, mounted RIGHT at the edge of the chassis. Use the Ctrl button to raise them off the ground, and have them pointing out of the chassis edge. You should then be able to attach the HPZ's directly to them if you get the position right.
5125
« on: August 03, 2011, 03:41:12 PM »
You should position the battery between the RADs instead of on top of them. Then you can make the chassis lower, and move the BA's back as close to the RADs as you can.
5126
« on: August 03, 2011, 03:37:37 PM »
Since you created the topic.
Have fun. =D
5127
« on: August 03, 2011, 03:36:32 PM »
No, Garvin's just trolololing.
5128
« on: August 03, 2011, 03:22:06 PM »
Wrong member, Garv.
And the mini wheels are on RADs, but the battery is above them. If it was positioned between them, the chassis could be lower and thus lighter.
5129
« on: August 03, 2011, 03:20:36 PM »
I should be AU.
Stop posting immediately.
5130
« on: August 03, 2011, 03:15:36 PM »
The pinks aren't necessary, I'd remove them. And fitting the chassis around your components is a good habit to get into. But if you rotate the Snappers so the HPZ are inside the chassis for added protection.
5131
« on: August 03, 2011, 02:58:09 PM »
Well, he does have a 5% warn now. So at least something happened.
5132
« on: August 03, 2011, 02:49:11 PM »
I'd say it was precedent more than anything. If he doesn't get at least a warn, we'll have a whole flurry of people accusing him of favouritism and such, wondering why they get a warn and he doesn't.
5133
« on: August 03, 2011, 02:46:20 PM »
The screenshot lost quality because it's a .bmp file. It just deletes pixels to make it all fit together.
And REMOVE THE FRONT WHEELS.
5134
« on: August 03, 2011, 02:34:17 PM »
I was also sure of that. *c*
Yep, they do.
5135
« on: August 03, 2011, 02:33:22 PM »
Remove the front wheels entirely. The robot will slide along on its front end, and it will be easier to turn.
5136
« on: August 03, 2011, 02:32:04 PM »
Thank you, Sage. =) I must not have read the instructions properly.
5137
« on: August 03, 2011, 02:29:18 PM »
You fire BEFORE you add the axle mount? That would be where I've been going wrong...
5138
« on: August 03, 2011, 02:26:52 PM »
Just a question but when I snapper load with Snapper II's, my motors get very flimsy and wobble. Is there a suitable way to fix this.
Not really, that's just as a result of their low torque. If you mount them on a Snapper2 or a Servo, then there's much less vibration involved. But what you can do is try to have the axis of rotation of the SnapperII and the axis of rotation of the weapon motors perpendicular to each other.
5139
« on: August 03, 2011, 02:24:49 PM »
I did that and then the rest of the steps but hax mode didn't work...
Occasionally it doesn't work for me either. I sometimes try pausing after I fire and that helps, but I'm not sure. I think you might have to do it all in one go, but once you've fired, do NOT switch tabs, otherwise it stops working.
5140
« on: August 03, 2011, 02:22:21 PM »
A Black and a Nifty should the trick
No.
1 black.
1 black could help you survive about 2 1/2 minutes with 4 HPZ's. A nifty could boost this to about 4.
Nifty's are the best give back weight wise.
Pinks = 100
Nifty = 400
Black = 800
I think so.
Fixed. HW HS normally require 2 Blacks. And you should really learn Snapper Loading if you want to build HS effectively, it's one of the most important glitches you can use to make as much weight as possible for weaponry.
|
Show Posts