This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - ayak420
41
« on: August 07, 2011, 06:40:10 PM »
I have been thinking about changing the wheels and I can't figure out how to mount the weapon without the extender. Also this just happened:  And I am messing around with a VS or Gut Ripper.
42
« on: August 07, 2011, 04:27:23 PM »
 Can't get the weapon motor to attach without the extender and the tecno wheels are not big enough for invertible driving
43
« on: August 05, 2011, 08:57:01 PM »
Added the overkill wheels and redesigned to rear protection to fit.  It is quite funny how this bot started out and where it is now.
44
« on: July 21, 2011, 11:17:25 PM »
After fighting with the new version of the bot I have found that the disc is almost useless when the bot is riding around upside down. The problem is the dual perm is higher off the ground then the wheels but if I change any of that the disc will not be as efficient of an undercutter. Anyone have any solutions to this?
45
« on: July 20, 2011, 09:51:43 PM »
Steel 5mm
46
« on: July 20, 2011, 07:57:01 PM »
So this is what I came up with. So far the largest hit I gave out was over 6000. 
47
« on: July 19, 2011, 09:11:36 PM »
Changed a lot but it is realistic. 
48
« on: July 18, 2011, 09:07:42 PM »
So here is the updated version. Back to HW, added two more drive motors to fix control issues, and changed the hammers to the 60 kg. 
50
« on: July 13, 2011, 07:38:59 PM »
So here is the new version that I just whipped up. The angle motors spin towards the center of the bot to keep opponents in the middle. Had no weight to spare for the ram plates. 
51
« on: July 10, 2011, 08:31:25 PM »
I liked the look of the second version with the chained spinners at the top on a wedge. I would go with that type of chassis, put some ramplates or something on it on the wedge, and some rad hs or something else.
Would the ram plates stop bots from getting up to the killzone and what do you mean by rad hs?
52
« on: July 09, 2011, 10:26:07 PM »
Here is the newest version of the bot. 
53
« on: July 09, 2011, 06:45:09 PM »
Here is the updated version, it is now a middleweight fighter. Can someone point me to a page that has a tutorial for AIing my bot. I am a bad driver so it is hard to tell if it is the bot or me. 
54
« on: July 09, 2011, 05:43:59 PM »
Here is the updated version. I do not think that there is a way to stack the weapons because the weapon is the 7th part attached to the base. Kept the drive motors outside to help with control. Does anyone have any ideas about protecting them? 
55
« on: July 09, 2011, 04:08:54 PM »
Need help with my HS. Keep getting killed by everything and it is starting to get annoying. So here it is  Right now I am working on shrinking the chassis, really need help on dealing with the wedges.
56
« on: July 09, 2011, 03:45:09 PM »
Here are two bots that I have been working on. Both have two HP Zteks stacked as weapon power, two HP Zteks as drive, and two Black Batteries for power. Terrorstorm 4 674.0kg HW VS  TerorStorm 4.1 689.3 HW VS 
57
« on: September 12, 2010, 12:13:03 AM »
What does eFFe mean?
58
« on: September 11, 2010, 09:51:00 PM »
They both have the default armor on them. This is the upgraded rammer. I shrank the chassis, got rid of the back armor, and added more spikes.  Here is a second version of the rammer.  As for the second one for it to be effective I am going to need to go past the 800 limit. The drive and batteries are just to much.
59
« on: September 10, 2010, 03:25:53 PM »
Thanks for the ideas. The second one is actually a horizontal spinner the way the wheels are configured allows it to move forwards back left right and on diagonals.
60
« on: September 10, 2010, 06:47:51 AM »
New here thought I could use some advise on a couple of my bots First one is called Rammington Steel  6 Z-Tek HP Drive 1 Snow Plow 2 Snapper About 15 Iron Spikes The other is called The OmniSmack  8 Z-Tek HP Drive 1 Z-tek HP Spinner 6 Iron Spikes
|
Show Posts