This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - haz
Pages: 1 ... 10 11 12 13 14 15 16 [17] 18 19 20 21 22 23 24 ... 42
321
« on: October 16, 2011, 03:44:03 PM »
this calls for one thing.... total rebuild! 
322
« on: October 16, 2011, 02:29:08 PM »
kidderminster:
did pretty well fw wise for me at this event, i moved forwards in all 4 fights, but in the last two i was OOTA'd by the dastardly shwxplosion again
323
« on: October 15, 2011, 01:49:13 PM »
to right it does boy, i remember this robot when it was a pie and mash shop....ooohheeyy it's comin' outa me like a yella cable  good thinking
324
« on: October 15, 2011, 09:21:19 AM »
i kinda want to call it the nightmare of milky joe.... vire is quite good though
maybe "In Locusta"
325
« on: October 15, 2011, 06:17:08 AM »
snot a "N00b" question, yes it is powered by brushless stuff, its a 12g outrunner motor running though a hobbywing 10a esc and a 7.4v 180mah lipo.
about £40 without radio gear, £90 with.
326
« on: October 15, 2011, 06:10:56 AM »
nope, open to suggestions. thanks btw
327
« on: October 15, 2011, 06:00:56 AM »
new fleaweight, drum spinner this time
328
« on: October 13, 2011, 11:39:42 AM »
329
« on: October 12, 2011, 02:10:20 PM »
im going to "pop" down, its only a 3hr drive so what the hey
330
« on: October 10, 2011, 03:43:16 PM »
with a 1mm material there isnt much point, its easyer to put paper or thin plasitc on the front instead
331
« on: October 10, 2011, 03:35:15 PM »
cool, might do that  new fw layout 
332
« on: October 10, 2011, 03:33:17 PM »
on polycarb? scissors seem to cut it pretty staight 
333
« on: October 10, 2011, 03:20:40 PM »
why sand it down?
334
« on: October 10, 2011, 02:06:08 PM »
there arent many as its the end of the year (ish)
aws bristol
atc oxfordshire
335
« on: October 10, 2011, 02:02:00 PM »
well antweight events move around a lot more than roaming robots
336
« on: October 10, 2011, 01:49:23 PM »
best to replace them after spinners get to them though
337
« on: October 10, 2011, 01:43:54 PM »
nick some of those lamanating sheets of thin plastic and then put that on the polycarbonate for 0mm ground clearence
338
« on: October 10, 2011, 01:32:43 PM »
what do you mean buy sharp edges, its plastic so it wont be sharp
339
« on: October 10, 2011, 10:20:25 AM »
i don't know, i personly find them quite anoying
340
« on: October 10, 2011, 10:01:44 AM »
Pages: 1 ... 10 11 12 13 14 15 16 [17] 18 19 20 21 22 23 24 ... 42
|
Show Posts