Messages

1

Stock Showcases / Re: Robots FTW stock showcase

« on: August 19, 2015, 03:13:32 PM »

Decided to do some ra2 building again. this is what i came up with


insides



my observations:

there is some empty space between the piston but i can not see how that can be eliminated but mounting the air tank longways instead of sideways (but that would result in a longer and narrower chassis which would narrow the stance.

Two iron spikes on the third weapon rack which may seem not needed but i am not sure what i could do with the additional 20kgs

Maybe you can use a SnapperII for the wedge and use one extender for the top plow. That might save some kgs.

thanks for the suggestion redace believe or not i did not need to remove one of the extenders holding the plow since using a snapper II for the wedge saved more than enough weight to get it down to a MW. 

2

Stock Showcases / Re: Robots FTW stock showcase

« on: August 18, 2015, 04:39:35 PM »

Thank for the comment redace I will try using a snapper II for  the wedge and see how much weight it saves. And believe it or not I have been fiddling about with the extender setup for the plow with your exact suggestion ooh the irony 

3

Stock Showcases / Re: Robots FTW stock showcase

« on: August 18, 2015, 03:44:20 PM »

here are the insides again as you asked sage not sure if you are able to see everything.

4

Stock Showcases / Re: Robots FTW stock showcase

« on: August 17, 2015, 03:59:33 PM »

Sorry for double posting but i have redone the extender setup for the plow and the RAD AND was just wondering which extender setup you would suggest

would it be this : (the face spinners are wider for the same weight (3 20cms instead of 1 40 cm and 20cm )


or the extender setup suggested by pwnator:


i am still unsure of how to shave off enough weight to keep DSA
 
I will also be posting a new bot soon tomorrow after school (UK time)

5

Stock Showcases / Re: Robots FTW stock showcase

« on: August 16, 2015, 12:22:36 PM »

I think Impending Doom has the motors rotated one more notch upwards, but the main problem is getting the mounting setup right. Try to have the main extender hold the plow and an extender attached to it that holds the RAD.

Come to think of it, Scrap Daddy's version has the black rotated the other way for a wider stance IIRC. It should be somewhere in his showcase.

thank you pwnator i have just tried your suggestion and it has definately improved the weapons  like reier said the first version struggle to ko when as the new one manages to ko in under 20 seconds once it gets under the opponent . unfortunately it is still 6 kgs overweight  with dsa as i changed the 5 20cm extenders to a 140 cm square entender (the one that weighs 5 kgs) for the wedge

6

Stock Showcases / Re: Robots FTW stock showcase

« on: August 16, 2015, 10:20:49 AM »

eco you might want to wait until you're a bit more experienced before giving a lot of advice man, this is not a bad robot nor is it an uncommon setup especially for a new player

hey RFTW welcome to the forums.
good start for a bot, I'm not really the best at stock but the main thing I can see to improve on this probably opening the disks a bit. It seems like they way it is now would be hard to actually hit anything with, and if you made them more facing forward I'd imagine it'd help. It's a good start though, you know axle loading and stuff already it seems so I assume you've checked out the beetlebros ra2techs page.


Try out DSL and Ironforge if you haven't already :) looking forward to see what you come up with next.

thank you reier i will try to get the disks more facing forward. i am just  wondering how i would go about doing that though . would i need to use the bottom attachment point of the RAD or would i need to think about redoing the extender setup?

7

Stock Showcases / Robots FTW stock showcase

« on: August 16, 2015, 07:01:30 AM »

Hello everyone i thinks its about time that i start my own showcase. i originally tried to start a showcase a few days ago however the original copy of ra2 i had on my laptop would constantly crash when i tried to take a screenshot (reinstalling it didn't help) so i tried to get ra2 on my dextop computer.


but anyway this is the first bot i am going to showcase


its underweight i know. i tried to have DSA on it by rebuilding it but it was 11 kgs overweight so unfortunately it has plastic armor 
also the wedge sucks for some reason and i dont know why. XZAI 2 and Mutiny get under it everytime when my bots wedge collides with theirs

insides:


Comments and constructive criticism are greatly appreciated  (although please try not to be too harsh)