Suede's DSL Showcase

[Gauche Suede]

Looks very good

this bot is for Total Annihilation 2(BEWARE), and also for my challenge against logannaruto/plazmic/sam.

[martymidget]

That plow/firestorm setup looks very familiar...hmm...I can't quite place where I know it from though...

And also unrealistic if those side razors do what I think they do.

[madman3]

That plow/firestorm setup looks very familiar...hmm...I can't quite place where I know it from though...

And the chassis too :P

[Naryar]

yeah it's totally not one of 123's builds

[Gauche Suede]

That plow/firestorm setup looks very familiar...hmm...I can't quite place where I know it from though...

And also unrealistic if those side razors do what I think they do.

those razors act as a Pulse 2(the bot in Sage's sig which have 3 battleaxes)like weapons, and if you look seriously close there's still a leftover space for the firestorm flipper to exist in real life.

That plow/firestorm setup looks very familiar...hmm...I can't quite place where I know it from though...

And the chassis too :P

it's from Fat Rat(but my bot had trovved chassis, cause 123 ignored the message EMPTY SPACE when building it...)

[martymidget]

it's from Fat Rat(but my bot had trovved chassis, cause 123 ignored the message EMPTY SPACE when building it...)

This is because nobody used the trov glitch when 123 built it, therefore it probably crossed nobodies mind. And bashing 123 is a really bad idea for you...

And I still wouldn't allow it in a toruney anyways. A tiny space hardly constitutes as standard DSL. Though most people seem to think it does now...

[Gauche Suede]

it's from Fat Rat(but my bot had trovved chassis, cause 123 ignored the message EMPTY SPACE when building it...)

This is because nobody used the trov glitch when 123 built it, therefore it probably crossed nobodies mind. And bashing 123 is a really bad idea for you...

And I still wouldn't allow it in a toruney anyways. A tiny space hardly constitutes as standard DSL. Though most people seem to think it does now...

yeah, actually i added the firestorm flipper because the bot was really underweight when i finished it(720ish) and to make sure that no HS or SS gets a lucky shot at the chassis. And ok i'll change the lower weapon's end postition so that the bot isn't unrealistic anymore.

[SKBT]

Double posta

should be sleeping now, but here's the 8th version of Midnight Sky:
(Image removed from quote.)
Midnight Sky 8 have 12 Razors on 4 BSGs, it haz PL10 armor, and weighs 799.1kgs without smartzone. The bot's wedge is on par with Beautiful Oblivion.

your wedge setup is stupid. the small wedges fall pretty quickly and dsl bars suck as wedges. switch to a 1/2 sheet and small wedge combo so once the other wedges fall off you will still have a wedge.

[Tweedy]

Double posta

should be sleeping now, but here's the 8th version of Midnight Sky:
(Image removed from quote.)
Midnight Sky 8 have 12 Razors on 4 BSGs, it haz PL10 armor, and weighs 799.1kgs without smartzone. The bot's wedge is on par with Beautiful Oblivion.

That's also the same as one of my builds just with firestorm flippers and plows

[madman3]

Double posta

should be sleeping now, but here's the 8th version of Midnight Sky:
(Image removed from quote.)
Midnight Sky 8 have 12 Razors on 4 BSGs, it haz PL10 armor, and weighs 799.1kgs without smartzone. The bot's wedge is on par with Beautiful Oblivion.

your wedge setup is stupid. the small wedges fall pretty quickly and dsl bars suck as wedges. switch to a 1/2 sheet and small wedge combo so once the other wedges fall off you will still have a wedge.

His wedge setup is also way too thin considering the overall width of the bot.

[Gauche Suede]

Double posta

should be sleeping now, but here's the 8th version of Midnight Sky:
(Image removed from quote.)
Midnight Sky 8 have 12 Razors on 4 BSGs, it haz PL10 armor, and weighs 799.1kgs without smartzone. The bot's wedge is on par with Beautiful Oblivion.

your wedge setup is stupid. the small wedges fall pretty quickly and dsl bars suck as wedges. switch to a 1/2 sheet and small wedge combo so once the other wedges fall off you will still have a wedge.

His wedge setup is also way too thin considering the overall width of the bot.

ok... so list of improvements for the bot:
1.make wedges wider
2.use half sheets for wedge extenders

yeah.... i'm going to rebuild this bahwt anyways because the wedge got AGOD and it can't self-right.
Comning soon: Team Hundred Acre Wood...

[090901]

yeah i have to agree with naryar it totally doesnt look like this

Another Popup.  This one pops from the inside, which unfortunately means it's doesn't have sirmech.

(Image removed from quote.)

 

[madman3]

yeah i have to agree with naryar it totally doesnt look like this

Another Popup.  This one pops from the inside, which unfortunately means it's doesn't have sirmech.

(Image removed from quote.)

Nah the bot's more like fatrat in terms of chassis and setup.

[martymidget]

If anything its most like my ripoff of fat rat that was in COTT, Rather Large mouse. :L

[Gauche Suede]

bot for my challenge CW IRL Flipper with avalanche:                                                              yeah it sucks. 531.0,Pl 10, 9 ants.

[Tweedy]

Post a picture of it from the bot lab because from here it doesn't look IRL

[madman3]

Yeah dude that doesn't look IRL. IRL flippers only look good if the flipper is either Subzero/Scraptosaur 2 esq or have a slot in a chassis (like Ceros or Dantomkia).

[martymidget]

Lol what.

As has been said, hardly IRL. And second, its 69kg underweight..

[Gauche Suede]

Post a picture of it from the bot lab because from here it doesn't look IRL

will do, and already did it, and updated it also:

please tell me how to make it more IRL, i have no idea.

btw expect Piglet, Lumpy and Tigger in about 15 minutes.

[Pwnator]

Any complicated shape you make, would probably be better off if the shape was made via the chassis instead. The small wedge components still detract it from its purpose. The chassis front should be sloped according to the flippers, and the flippers should be very close to the lip of the chassis.


Basically, everything should be seamless.