Author Topic: Bubbleman's DSL Showcase (Read 25845 times)

somestrangeguy · « **Reply #40 on:** April 05, 2010, 03:13:02 AM »

0.2501 works for me, I make my bot heights always have 01 in the end to ensure that when replacing it for something else it does not mix it up with something like a components coordinates on the baseplate.

And when you replace you just press Replace All and it will all be done in a single click, every bot has different amounts of replaceable numbers, the less dots you used in Chassis Desing, the less numbers are needed to be replaced, so dont worry about it if your bot has more or less than 12 as shown above. Aslo you are propably going to have to cahnge the orientation of your controlboard tough, because .2501 is too low for it to be that side up, atleast for me.

ACAMS · « **Reply #41 on:** April 05, 2010, 03:27:16 AM »

Quote from: Bubbleman on April 05, 2010, 03:05:20 AM

ok, do i size down the picture in paint by draging the picture inwards to the robot screen?

https://gametechmods.com/forums/index.php?topic=2143.0

Bubbleman · « **Reply #42 on:** April 05, 2010, 04:26:48 AM »

Quote from: somestrangeguy on April 05, 2010, 03:13:02 AM

0.2501 works for me, I make my bot heights always have 01 in the end to ensure that when replacing it for something else it does not mix it up with something like a components coordinates on the baseplate.

could you tell me a rough height where the bot becomes invertible with hypno wheels, because I know that would reduce the height quite a bit but I want it to be just invertible, like just 2 pixels off the ground.

Pwnator · « **Reply #43 on:** April 05, 2010, 04:31:22 AM »

My guess would be 0.338182, though it might be a notch higher than that. But that's the height I usually aim for if I don't want to use a halfsheet. :D

Naryar · « **Reply #44 on:** April 05, 2010, 04:32:42 AM »

^^ Yes, hypno invertibility is feasible with 0.338182.

Bubbleman · « **Reply #45 on:** April 05, 2010, 01:31:04 PM »

thanks. i will try what you said.

Bubbleman · « **Reply #46 on:** April 10, 2010, 02:07:56 PM »

Sorry for the big delay, im having a builders block...
wondering what i should make...

Bubbleman · « **Reply #47 on:** April 11, 2010, 04:05:52 AM »

Triple posting because...well, just because!

1mm plastic, 2 ants, style if a pinner (please tell me if its a new style).
how it works:
#1:push enemy bot against wall
#2:keep pushing when opponent hits wall to pin him there.
#3:(if not in Kenzorg ICG arena skip to #4) opponent will be damaged by fence. if you keep him there long enough he will be destroyed. you do not have to read #4 if you were in the Kenzorg ICG arena.
#4: immobilization counter will start counting down. when it reaches 2 back away. the opponent will not react quick enough and will be counted out. if the opponent's counter is lower than yours, do not back away.

comment please!

Avalanche · « **Reply #48 on:** April 11, 2010, 04:08:14 AM »

Very good.What are those drives?Cant see.

Sparkey98 · « **Reply #49 on:** April 11, 2010, 04:09:54 AM »

pinners are new. well, I made a stock bot just for pinning back in the day..........................

Pwnator · « **Reply #50 on:** April 11, 2010, 04:15:40 AM »

Pinners aren't new. The special AI for pinners is. And those are copals, if I'm right.

G.K. · « **Reply #51 on:** April 11, 2010, 04:35:26 AM »

Nah they're astros.

SKBT · « **Reply #52 on:** April 11, 2010, 07:13:05 AM »

~~On the pinner try using tornado wheels instead of tazbot wheels. They have better grip so that means more speed for the same weight.~~

Edit: ignore my advice!! I didn't look closely at it and goofed.

Pwnator · « **Reply #53 on:** April 11, 2010, 07:18:14 AM »

Those are micro wheels. Wide ant wheels would be better for lower ground clearance. :D

Bubbleman · « **Reply #54 on:** April 11, 2010, 01:50:19 PM »

@G.K.: yeah you're right.
@Pwnator: higher ground clearence is better than low ground clearence because 30cm plates dont work and the 45-45 plate attaching the scoop to the disc wouldn't work...trust me on this, i've tried it!

Bubbleman · « **Reply #55 on:** April 12, 2010, 01:41:44 PM »

Call me a Mage 'cause i'm reviving the topic!

DSA.

3mm Tite.

Comment Please!

G.K. · « **Reply #56 on:** April 12, 2010, 01:44:09 PM »

Firstly, never use DSA in DSL. It is useless. Plastic 1 pwns it. You could use aluminium 3 for the same weight.

Ok. The first AW looks awesome, but it's under-weaponed and the current weapon will to hit anything. Increase the chassis size so you can have astros, downgrade to them. Upgrade to wide ant wheels, and add more weapons.

Use wide ant wheels on the plow one.

Bubbleman · « **Reply #57 on:** April 14, 2010, 10:41:27 AM »

i can't belive i havent gotten more replies...
@G.K. ok, on the first ant when i built that i was haveing a builders block and wanted to make something.

second ant, yeah, i'll do that.

Naryar · « **Reply #58 on:** April 14, 2010, 02:54:57 PM »

Yes, invertibility is a requirement on a pusher.

Bubbleman · « **Reply #59 on:** April 15, 2010, 01:57:24 AM »

Quote from: Naryar on April 14, 2010, 02:54:57 PM

Yes, invertibility is a requirement on a pusher.

? why did you say that?