Vertigo's Stock Showcase!

[Vertigo]

wrong and wrong :P

you can use more then one plastic extender to easily replicate that setup without the need for the angles.
Yes, but that would make the same weight anyway

and there is a lot of space to be saved.. 2 of those DDT's could be added to plastic extenders on the Blue Snapper to allow you to halve that middle section and make the whole chassis a C shape.
How? Note that the ramplates are attatched to the blue snappers aswell

thats how I would do it anyway :P

[JoeBlo]

build with 20 cm extenders that will give you enough attach options for what you need...

[Vertigo]

^Better?^
Don't know what I can do for front protection, tried lots of time but its difficult because the ddts stick out so much.
Surprised by the wedge quality, not the best, but I expected them to suck. Gets under rabid pit bull but not neglected waterbug

[JoeBlo]

much better (wasnt so hard was it :P)

you could get frontal protection with an angled baseplate in the middle of the DDT's and a few extenders?

or redo the anchors part to include ramplate attaching like S13 

or if someone else *looks at Pwnator* has another idea

[Pwnator]

Actually, I'm think of a setup right now that won't make it look too much like Solstice and doesn't need to have a chassis overhaul.

[Vertigo]

Actually, I'm think of a setup right now that won't make it look too much like Solstice and doesn't need to have a chassis overhaul.

Which is...

[Vertigo]

Made a decent setup (I think):

Side wedges are only there because I had free weight

[Gazea2]

Not bad. You have my approval (if you are going to use it for the pack) . Try and add some side armour instead of the side wedges.

[Vertigo]

Not bad. You have my approval (if you are going to use it for the pack) . Try and add some side armour instead of the side wedges.

Tried that, didn't work very well, but I'll try again

[Sage]

Hmmm. A popup with undercutting RAD HS?? Where have I seen that before....

[Vertigo]

Hmmm. A popup with undercutting RAD HS?? Where have I seen that before....

Yeah, but mines more of a popup, & yours is more of an 'undercutting RAD HS'

[Vertigo]

Plan C:

DSA

[R0B0SH4RK]

You could probably rotate the snapper 180 degrees, have a 20cm extender with the side APs facing up, mount the t-connector off of that, attach the HPZs directly to the T connector. Then, attach another 20cm extender to the first one and put the plow there. Then, you'd get a more compact setup with better reach behind you.

[Vertigo]

You could probably rotate the snapper 180 degrees, have a 20cm extender with the side APs facing up, mount the t-connector off of that, attach the HPZs directly to the T connector. Then, attach another 20cm extender to the first one and put the plow there. Then, you'd get a more compact setup with better reach behind you.

I'll try that, in the meantime...

*Name would be appreciated*, my first stock juggler :D
Better wedges that I expected, gets under everything in BBEANS AI apart from Seism 13, R4, & 70 - 40 Magnum or whatever its called
DSA, two ddt wedges (small wedges just cut off from view), 2 supervolts, 4 HPZ - Rubber drive, tribar setup

[Vertigo]

No Comments? 

[NFX]

It looks okay, I reckon if you move the spinners back a little, the opponents should ride up on top of them a little better.

[Vertigo]

Opponents 'ride up on top of them' quite well actually, but I'll probably change that when I re-built it, (which must happen at some point)

[NFX]

I'm surprised they do, the weapons overhang the top of the wedge quite a lot.

[Vertigo]

I'm surprised they do, the weapons overhang the top of the wedge quite a lot.

So was I, they sort of 'scoop up' other bots

[J]

I'm surprised they do, the weapons overhang the top of the wedge quite a lot.

So was I, they sort of 'scoop up' other bots

Somewhat like a pitching machine, except it keeps them pinned on the plow. Right?

and I think if you used extenders instead of the tribar, you might save weight
Nvmd, that would kill the exactly 800 weight thing.