Author Topic: RpJk's Stock Showcase: "Bring out your dead and unfinished design." (Read 103392 times)

Pwnator · « **Reply #740 on:** November 07, 2011, 06:31:23 AM »

Quote from: That Robot is a Spy! on November 07, 2011, 06:27:05 AM

You do not need 4 HPZ's as drive.

nope.avi

RpJk · « **Reply #741 on:** November 07, 2011, 09:58:59 AM »

Quote from: That Robot is a Spy! on November 07, 2011, 06:27:05 AM

You do not need 4 HPZ's as drive. Have 2 and add some more irons.
Also, how many Supervolts, I can only see one.

2 supervolts and keeping it as 4 HPZ's.

NFX · « **Reply #742 on:** November 07, 2011, 11:08:42 AM »

This style of VS probably does need 4WD. Good work with the axle loading, though. I would attempt to tighten up the chassis, though, and I'm not entirely sure 16 Irons would be enough. If the wedges are good enough, then you may be able to get away with it if the underside isn't terribly protected.

Mr. AS · « **Reply #743 on:** November 07, 2011, 02:29:01 PM »

Use Green Snappers for the wedge.

Thyrus · « **Reply #744 on:** November 08, 2011, 05:26:48 PM »

extra weight!

ty4er · « **Reply #745 on:** November 11, 2011, 12:41:28 PM »

~~Thyrus giving advice on a normal bot? :O~~

Change the DDT's for snappers (if they make better wedges) and put them inside so they won't easily get ripped off and maybe get a few more weapons.

Otherwise it doesn't look too bad.

Naryar · « **Reply #746 on:** November 11, 2011, 03:04:00 PM »

It seems very lightly weaponed to me. I would just do lighter extender work, dump these wheels for shinies, and maybe remove the plow.

And keep the DDT's, 'cause it will make the wedge better. You will be able to selfright with DDT's better, because I somehow doubt the ability of your weapon to selfright the bot on it's own.

ty4er · « **Reply #747 on:** November 11, 2011, 03:49:30 PM »

Quote from: Naryar on November 11, 2011, 03:04:00 PM

And keep the DDT's, 'cause it will make the wedge better.

~~You dare defy the mighty InfiniteInertia? :O~~

Well whatever makes the wedge better...

Scorpion · « **Reply #748 on:** November 11, 2011, 04:00:03 PM »

Nobody's 100% sure whether DDT or green snapper wedges are better really, i'd say DDTs in this case because of self righting as Nar said.

RpJk · « **Reply #749 on:** June 20, 2012, 12:55:24 AM »

Bump

Getting back into buliding for summer

Remade Psynergetic Theory.
A bit unstable but does not look too bad.

NFX · « **Reply #750 on:** June 20, 2012, 01:28:28 AM »

It looks cute. But those stabilisers should ideally be longer. Maybe Samurai blades might be a better option. if you dropped down to one caster, and placed it in the center to protect that vulnerable T connector, that may give you the weight for it.

Jonzu95 · « **Reply #751 on:** June 20, 2012, 01:30:17 AM »

Maybe you could tighten the chassis and rebuild the extender arms...

Fracture · « **Reply #752 on:** June 20, 2012, 06:09:34 AM »

Yeah just mount the RADs normally.

Wacky Bob · « **Reply #753 on:** June 20, 2012, 06:52:06 AM »

Try angling the disc a little bit to protect the motor

RpJk · « **Reply #754 on:** September 08, 2012, 07:34:13 AM »

Tried buiding something so I decided to bulid a rammer, then I could not contiune buliding because I am crap.

So I need your help hopefully for the last time,

So I change the bot into a popup or VS and if so how? Because I am not changing the chassis.

Skiitzzox220 · « **Reply #755 on:** September 08, 2012, 07:45:11 AM »

Quote from: RPJK on September 08, 2012, 07:34:13 AM

So I change the bot into a popup or VS and if so how? Because I am not changing the chassis.

Well you're not going to get anything done then. One of the main principles of stock is re-building the chassis, everyone will tell you this.

RpJk · « **Reply #756 on:** September 08, 2012, 08:16:57 AM »

Quote from: Skiitzzox220 on September 08, 2012, 07:45:11 AM

Quote from: RPJK on September 08, 2012, 07:34:13 AM
So I change the bot into a popup or VS and if so how? Because I am not changing the chassis.
Well you're not going to get anything done then. One of the main principles of stock is re-building the chassis, everyone will tell you this.

Forget what I said.

I just also realized I can delete messages on my showcase.

ty4er · « **Reply #757 on:** September 08, 2012, 03:15:15 PM »

if you get rid of the anchors and stuff and axle load the snapper's axle out, you might be able to put another snapper in and have around 4 razors there. it would also be best if you made the chassis wedge a lot wider

you can probably go down to normal z-teks aswell

RpJk · « **Reply #758 on:** September 09, 2012, 06:33:00 AM »

DSA, Stacked razors, all you can see there.

Wedge is terrible though.

NFX · « **Reply #759 on:** September 09, 2012, 06:49:40 AM »

You can improve the wedge with some fine tuning of the Snapper angle. Tedious, but necessary to win the wedge war, I'm afraid. If you shorten the popup arm, you could eFFe a third 20cm+razor on there for some added DP.