Text Only | Text with Attachments

gametechmods

Robot Arena => Showcases => Stock Showcases => Topic started by: Gropaga on February 28, 2012, 05:55:14 AM

Title: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: Gropaga on February 28, 2012, 05:55:14 AM
This is my showcase.
I made a Wedge/Hammer Hybird bot.WeeeeeeeeeedgeRaptooooooor!
(http://i.imgur.com/adv1W.png)
(i know it is unbalanced)
I removed pink affter this.　weight affter removal of pink:379.6
Question:How to get Starcore AI?
I Killed Emergency.(Emgergency had a Clickbeetle's fliper.Py)

 
Title: Re: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: Wacky Bob on February 28, 2012, 06:31:07 AM
You can get Starcore AI from the AI section on the Main Page.

Good job building to the weight limit. That's a lot of extender work on the snow plows though. It might be better to get rid of them and use them for more weapons. Also, Shiny Hubs would be the better wheel choice and ballasts are pointless. And if you can, try adding wedges.

Title: Re: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: Gropaga on February 28, 2012, 07:03:49 AM
Quote from: Wacky Bob on February 28, 2012, 06:31:07 AM
You can get Starcore AI from the AI section on the Main Page.

Good job building to the weight limit. That's a lot of extender work on the snow plows though. It might be better to get rid of them and use them for more weapons. Also, Shiny Hubs would be the better wheel choice and ballasts are pointless. And if you can, try adding wedges.
Okay, but shiny hubs Dosen't are too small to touch the ground with snowplows being used as spinner killer
Title: Re: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: Wacky Bob on February 28, 2012, 07:16:38 AM
You could just use casters like this instead:

(https://gametechmods.com/uploads/images/82097Casters.PNG)

Anything connected directly to the baseplate is invincible
Title: Re: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: Mr. AS on February 28, 2012, 02:29:58 PM
you can easily clean up that extender work holding the plows
Title: Re: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: Gropaga on March 06, 2012, 05:24:38 AM
I need help with Axle loading.
 
(note:i don't want link to sage's videos)
Title: Re: Gropaga's Stock Pursbosforkerso(Gropaga's Stock Showcase)
Post by: 40757 on March 06, 2012, 05:45:26 AM
Set down a control board and battery. Connect an extender and RAD to the axle you want loaded. Wire the original axle and RAD to rotate when you press ___ button.

1) Hold the button down for 3 seconds, then swap to another tab on the top once.
2) Keep swapping between tabs, but this time, swap it after holding the button for not even 0.5 of a second.
3) Do this until  the axle is out of place, and you can attach whatever you wanted on it.

If you don't hear the RAD squealing, then it's not going to axle load, and you'll have to redo the process from the first point.
Text Only | Text with Attachments