Author Topic: Gaz's Garage (Read 99322 times)

Pwnator · « **Reply #880 on:** June 04, 2012, 06:58:29 AM »

uuhhh

snapper load the wedge

the asymmetric look is killing me :/

Gazea2 · « **Reply #881 on:** June 04, 2012, 07:03:39 AM »

Oops, didn't think about doing that.

NFX · « **Reply #882 on:** June 04, 2012, 07:09:12 AM »

I agree with Pwn, asymmetric wedge isn't going to do well. You can axle load it out of the way, then attach the Snapper2 for the weapons. Is the CB under the Nifty?

Gazea2 · « **Reply #883 on:** June 04, 2012, 07:20:29 AM »

Yeah the CB is stacked into the Nifty because the chassis is the exact height for Z-teks and it won't fit above it. I'll definitely test the bot out after that. What should I do with the extra weight?

NFX · « **Reply #884 on:** June 04, 2012, 07:21:28 AM »

Perhaps extend the front of the chassis a little so you can get the casters higher up. At the moment, they're quite low, and I'm concerned HS are just going to go straight over them.

martymidget · « **Reply #885 on:** June 04, 2012, 08:43:44 AM »

I found with just a nifty the snapper started to weaken after only a few hits, which is why I have the extra pink in mine :P

Badnik96 · « **Reply #886 on:** June 04, 2012, 08:51:53 AM »

nooooo why is everyone building popuuups

Gazea2 · « **Reply #887 on:** June 04, 2012, 08:59:35 AM »

Tested it and it seems to do fine so shhh Marty. :P

NFX · « **Reply #888 on:** June 04, 2012, 10:39:29 AM »

Good work, but is it possible to get the wedge and ramplate centered? It's going to annoy me quite a lot.

Something you could do is angle the rear of the bot to match the Z-tek slope, so it doesn't get stranded on its back.

ty4er · « **Reply #889 on:** June 04, 2012, 12:01:27 PM »

the unsymmetrical-ness makes me cringe a little but otherwise it looks nice

R0B0SH4RK · « **Reply #890 on:** June 04, 2012, 05:32:46 PM »

Quote from: Gazea2 on April 30, 2012, 01:57:09 PM

Woah, page 3...

(Image removed from quote.)

DSA, 8 razors... I believe Scrap or Sage made something similar for ReStocked but hey-ho. That BA took so long to stack. >.<

247.something

Pwn made a version that wasn't invertable, but then I made the current version for Re-Stocked.

Gazea2 · « **Reply #891 on:** June 05, 2012, 11:58:42 AM »

^Ahh, ok. Thanks for clearing that up.
Anyway, another bot?! I haven't been this productive in ages...
Meet Spherimorph!

24 irons, 8 ice-picks, DSA and 1 black with CB stacked in.

FOTEPX · « **Reply #892 on:** June 05, 2012, 01:59:51 PM »

Looks badass, but fragile.

ty4er · « **Reply #893 on:** June 05, 2012, 02:48:43 PM »

looks awesome, can it self-right easily?

Sage · « **Reply #894 on:** June 05, 2012, 03:25:12 PM »

It's the worst bot I've ever seen.

Gazea2 · « **Reply #895 on:** June 05, 2012, 03:27:30 PM »

Teehee, you wuv it really.
From testing it seems like it can self-right fine which I was surprised about. Now I just need to re-install Starcore V4 and I can start some serious testing..

Edit: Also, showcase name change. yay more alliteration

Badnik96 · « **Reply #896 on:** June 05, 2012, 03:40:09 PM »

Awesome VS is awesome

I was gonna make something similar for MLP but then I got lazy.

Pwnator · « **Reply #897 on:** June 05, 2012, 07:09:28 PM »

You should ditch the icepicks on the discs and use the free weight to add more weapons onto the arms.

Mr. AS · « **Reply #898 on:** June 05, 2012, 07:23:38 PM »

yea, icepicks have normals so they wont do much at all like that.

Gazea2 · « **Reply #899 on:** June 06, 2012, 06:06:21 AM »

Awww guys don't be so picky
[/bad joke]

This next bot took so long to stack as anyone in the GTM skype group would know.
Omnis:

HS built off one axle which is stacked INSIDE the Nifty. I believe Sage did something similar. Spins relatively fast and no havok! :D
Might re-build later with the spinners side by side. I'll also probably add some extra razors or something to eat up the weight.