Author Topic: ty4er's showcase (Read 260058 times)

MassimoV · « **Reply #780 on:** January 21, 2012, 11:16:03 AM »

Yeah that would probably benefit the design. I still like it alot though.

ty4er · « **Reply #781 on:** January 22, 2012, 10:11:25 AM »

New vs:

I need to find a few kg's to get a longer sheet so it can actually move when inverted (plastic 1? it's tite 1 atm)

Squirrel_Monkey · « **Reply #782 on:** January 22, 2012, 10:25:37 AM »

Quote from: ty4er on January 22, 2012, 10:11:25 AM

New vs:

Where?

ty4er · « **Reply #783 on:** January 22, 2012, 10:31:08 AM »

Quote from: Squirrel_Monkey on January 22, 2012, 10:25:37 AM

Quote from: ty4er on January 22, 2012, 10:11:25 AM
New vs:
Where?

oop you know i meant hs

ty4er · « **Reply #784 on:** January 22, 2012, 11:23:09 AM »

and a mw

i probably should get rid of the flipper segments and put the drive on a skirt on the back.

MassimoV · « **Reply #785 on:** January 22, 2012, 12:13:35 PM »

That's a really good design.

Gazea2 · « **Reply #786 on:** January 22, 2012, 02:57:41 PM »

^This.
I agree with you, though. Putting the drive on a skirt on the back would decrease the amount of vulnerable extender work.

Naryar · « **Reply #787 on:** January 23, 2012, 04:36:54 AM »

Put your drive and stabilizers on an Alu 40cm sheet.

ty4er · « **Reply #788 on:** January 23, 2012, 12:22:44 PM »

done that, 2 hws now

1. HW to match the previous bots, if anyone can think of a better drive set up please tell me :P
2. HW version of that flamer/sns i posted a while back. Works very well, 2 poly sheets on the bottom for protection and 6 flamethrowers.

NFX · « **Reply #789 on:** January 23, 2012, 12:35:05 PM »

First one looks awesome, but unrealistic. I'd try to get the 40cm skirts a bit wider, then you should be able to attach the motors directly, while avoiding the stabilisers being cut. Second looks even more awesome, but looks a bit heavy for a HW. Insides?

martymidget · « **Reply #790 on:** January 23, 2012, 12:49:18 PM »

Quote from: NFX on January 23, 2012, 12:35:05 PM

First one looks awesome, but unrealistic. I'd try to get the 40cm skirts a bit wider, then you should be able to attach the motors directly, while avoiding the stabilisers being cut. Second looks even more awesome, but looks a bit heavy for a HW. Insides?

Not to mention the entire weapon interescts the half sheet. Nice idea, but it needs to be done differently for it to be realistic :P

The Ounce · « **Reply #791 on:** January 23, 2012, 12:52:49 PM »

I would like the first one better if the weapon was lower, or in some other position where it doesn't completely cut through the stabilizers. Just attach the angled skirts directly to the half-sheet, and use the second attachment point on the skirts to attach the drive motors. At the angle you'll need to have the skirts at, you might need another extender to make sure the wheels are touching the ground.

The second one looks okay, seems underweaponed, but that's probably because of the flamethrowers.

ty4er · « **Reply #792 on:** January 23, 2012, 03:13:29 PM »

In my mind i couldn't think of another setup, my mind just went blank. Sadly that's as low as i can get it without making it have a super weak point (or i cant think of one), even with one it would probably be too low.

The second one weighs 799.5 iirc, perfectly fine. the insides are 4 ants (could do with one more, not that hard) and a medium or small air tank. I should probably upgrade those npc's to fasts.

martymidget · « **Reply #793 on:** January 23, 2012, 03:20:05 PM »

Try using DSL bars for the drive and stablisers- it would make the stance wider and would not need the hex plates to put the drive on. However, I'm more worried about you fixing the fact that the weapon still intersects the halfsheet. xD

ty4er · « **Reply #794 on:** January 23, 2012, 03:21:39 PM »

blegh i'll just use a few ant blades until it doesn't intersect i guess, i just hope it doesn't scrape along the floor :P

martymidget · « **Reply #795 on:** January 23, 2012, 03:28:12 PM »

I think a setup with two multi's and a caster would be better- then you could raise the stabilisers to the right level. And to be honest, a caster is plenty for an undercutter.

ty4er · « **Reply #796 on:** January 24, 2012, 12:46:27 PM »

meanwhile:

is 28 close enough?

Squirrel_Monkey · « **Reply #797 on:** January 24, 2012, 01:20:12 PM »

28 is NOT 27
Needs more 27
3x9 will suffice
4x7 WILL NOT BE TOLERATED
Now for MOAR typhoon spikes.

ty4er · « **Reply #798 on:** January 24, 2012, 01:23:13 PM »

Quote from: Squirrel_Monkey on January 24, 2012, 01:20:12 PM

28 is NOT 27
Needs more 27
3x9 will suffice
4x7 WILL NOT BE TOLERATED
Now for MOAR typhoon spikes.

sorry mom

No typhoon spikes though, i'll just put a lds tooth in the middle :P

Badnik96 · « **Reply #799 on:** January 24, 2012, 06:00:54 PM »

Quote from: ty4er on January 24, 2012, 01:23:13 PM

Quote from: Squirrel_Monkey on January 24, 2012, 01:20:12 PM
28 is NOT 27
Needs more 27
3x9 will suffice
4x7 WILL NOT BE TOLERATED
Now for MOAR typhoon spikes.
sorry mom

^I rolfed at the above quote :P