By a fitting battery setup, he means to put in the right amount of batteries for the robot's power consumption.You forgot to count the mags.
At current state, you have 6 BattlePacks, which is equivalent to 15 ant batteries (the small orange ones). With your setup, you only need a minimum of 7 batteries: 1 for each drive motor and 2.5 for each BSG. This will give it enough power to go for the full 3 minute fight, though you may be a touch low on power towards the end. For that, you should probably have somewhere around 8 or 9 ant batteries in the robot.
Those numbers above, of course, are dependent on using your BSG's as flippers or not.
you have 6 BattlePacks, which is equivalent to 15 ant batteries (the small orange ones).
Did that, what else can I do?You can still send that in to replace your current bot, you can update before the splash is put up, which will like ly happen in either 5 or 6 days.
Also, I'm really wishing that I entered this into RIW3 instead of the pile of dogger that I actually did.
Rubbers are bit weak in DSL, I recommend to use Vlads. Also You could use lighter extender work on the wedges.Those are shines, not rubbers. :P
Whoops.. ^^'
Use the large control board.Rubbers are bit weak in DSL, I recommend to use Vlads. Also You could use lighter extender work on the wedges.Those are shines, not rubbers. :P
and your wrong jonzu, there is no reason for him to switch to vladsWhoops.. ^^'
Use the large control board.Rubbers are bit weak in DSL, I recommend to use Vlads. Also You could use lighter extender work on the wedges.Those are shines, not rubbers. :P
Vlad's got bigger HP.and your wrong jonzu, there is no reason for him to switch to vladsWhoops.. ^^'
Use the large control board.Rubbers are bit weak in DSL, I recommend to use Vlads. Also You could use lighter extender work on the wedges.Those are shines, not rubbers. :P
I don't like razors that much to be honest. They break too easily.
Is the bar cutting through the anchor?No, don't think so.
change the wheels to technos, add some lds teeth or something to the spinner and maybe a back support extender thing
For a HW that is horrifically underweaponed, I'm afraid.
Steel 10? Blech. I would make it much lower. Lower it enough so it could be MW. Maybe even a LW, but I doubt it...
Steel 10? Blech. I would make it much lower. Lower it enough so it could be MW. Maybe even a LW, but I doubt it...
DP
As I said before, I'm going to change the armour once I find a way to make it a lot heavier. Steel 10 is crap, I know.
just add some razors or light beater bars as i said earlier. and of course drop the armour to about plastic 5
Not bad. Metal Hinge Wedges are going to be very ineffective on a VS, I'd go for some angled stabilisers on ME's, personally. Perhaps swap for the S-shaped TWM motors rather than straight ones, they give you a wider stance, and you don't have to have the motors pointing behind the wheels.
its probably going to fail against fss and sns and hs, made the front widerand extenal armor would help aswell
(https://gametechmods.com/uploads/images/80051Moldarach.png)try reducing empty space, getting a wider front and try to get a ti sheet on a skirt hinge for wedge protection
Moldarach
Power: 5 ants
Armour: Tite 3mm
Locomotion: Hypnos on NPCFs
getting a wider front
and try to get a ti sheet on a skirt hinge for wedge protection
Good point :Pgetting a wider front
and try to get a ti sheet on a skirt hinge for wedge protection
Doesn't getting a tite sheet on the front give you a wider front anyways? :P
Needs moar batteries.
3 more(8)Needs moar batteries.
How many should I have?
i dont really like the salvager. hammer looks too awkward.Oh, damnit, forgot to say. Nazca's a MW.
nazca seems better though, if its a lw you would likely be better off with that one both aesthetics and performance wise
It's a DSL2.1 piglet, no one gives a damn about it being exposed.
Why ? 8000 HP.
It's a DSL2.1 piglet, no one gives a damn about it being exposed.
Why ? 8000 HP.
I just thought that it wouldn't be considered IRL if it was like that.
Really it's not bad. I'm just miffed one of the music notes is backwards.
It's these kind of robots that remind me I'm still a noob.
Skin looks good. Insides would be nice.Just cause I'm nice -
*ahem* insides? Don't use green control boards.
Never use those stock extenders. You need to strengthen the flipper's durablity, because one hit by any competent robot will render it useless.
I know. Just because it's IRL it doesn't mean you can't improve the effectiveness of your robot.*ahem* insides? Don't use green control boards.
Never use those stock extenders. You need to strengthen the flipper's durablity, because one hit by any competent robot will render it useless.
I didn't make this to be battle-effective, I made it to look nice.
I know. Just because it's IRL it doesn't mean you can't improve the effectiveness of your robot.*ahem* insides? Don't use green control boards.
Never use those stock extenders. You need to strengthen the flipper's durablity, because one hit by any competent robot will render it useless.
I didn't make this to be battle-effective, I made it to look nice.
I like it. Insides?
IIRC only things without normals are beater bars
IIRC only things without normals are beater bars
Yeah, it does show youve been away some time.
My advice:
The multis look ducking awful, pole spikes are not that good, just invest in a heavy plow which is fairly OP, and you could probably just use side connectors to have multiple spikes, perhaps iron spikes.
Im very confused here though: What version of DSL made pole spikes even slightly good?
Awesum, betr than ma bots omfgrofltrololobbq
So it's Velociraptor's wimpy cousin ?
Ramming, best censor, otherwise the mods can give you warnings and such and if i piles up you can get punished.
Nice bot :)
*clenches face after looking at the skin* GAAH MY EYES!!!!!!!
Ramming, best censor, otherwise the mods can give you warnings and such and if i piles up you can get punished.
Wut?
https://gametechmods.com/forums/index.php?topic=17404.msg668884#new (https://gametechmods.com/forums/index.php?topic=17404.msg668884#new)
New rules about warnings for things such as swearing and more dangerous stuff: Highly enforced.
Jackson Pollock eh?
I thought it was a tribute to Vinesauce NES & SNES Corruptions o.O
I don't like all that meme Pollocks.
xD sorry, bad joke.
Twas a decent jokeI don't like all that meme Pollocks.
xD sorry, bad joke.
Seen worse XD
I was telling him not to swear in the main forum because the mods will kill him due to the newer warning rules. Seriously, what was wrong there? At least i attempted to help.
Did I? O.oI was telling him not to swear in the main forum because the mods will kill him due to the newer warning rules. Seriously, what was wrong there? At least i attempted to help.
I didn't swear?
I was telling him not to swear in the main forum because the mods will kill him due to the newer warning rules. Seriously, what was wrong there? At least i attempted to help.He censored it though....
That the Yorkshire flag?
Yorkshire eh? Then I have a sponsor decal idea for it:
(http://i.telegraph.co.uk/multimedia/archive/01415/tetleyTea_1415142c.jpg)
Instead of making the sides of the dustpan parts of the chassis, just make them skirts or DSL bars.. That should widen the dustpan enough so you can get bots in.
Hey at least you aren't taking chassis damage.
implying you should be aiming to win in IRL and not just make something that looks IRL. But I know many disagree with me...
i would agree with a VS using axes in IRL if it looked cool enough.
This one however doesn't really look cool, and therefore using axes on a VS, as counterintuitive as it is, is pointless.
just so you know axes have normals => very bad for any kind of spinner.