LRA2's/Avalanche's DSL Robot Showcase

[Avalanche]

It gets under just fine with one, thank you very much.

[Gauche Suede]

It gets under just fine with one, thank you very much.

but that bot looks cooler with 2(and you got weight for it).

[Naryar]

Ok, will rebuild anti gravity 3 either tonight if bored or tommorow if too tired
Ive finished Anti Gravity 3.5.
(Image removed from quote.)
Innards
(Image removed from quote.)

That bahwt is pretty good, but add dual wedges and it'll be awesome!
(i'll obviously get repped down by nary again).And this is all that i can tell you. Someone better than me in IRL will tell you more.

amusing that when you post decent advice you think it's bad and when you post bad advice you have no problem with it.

[Avalanche]

Frankly im actually trieing to SHAVE weight of it to make it a Cruiserweight.
So thanks for some misaimed advice.

[Tweedy]

In IRL you shouldn't use metal hinge wedges, you only need to use ant batteries for the judge bursts ( not sure how many ) and doesn't the plate with beater bars in the middle stop bots from going up the wedges ?

[Avalanche]

Yes but by the time they are up there I get a definite flip.Are you saying i should just shave some weight by ditching the plates beater bars and the metal hinge?

[Tweedy]

If the beater bar plate stops bots from climbing the wedge then yes and the metal hinge should be removed either way which should give you a cruiser weight with weight left over for more armour.

[Gauche Suede]

Those top most Beater are useless, and the way you placed the flippers to the judge burst actually decreases flipping power, just put the flippers directly to the burst motor.

[Avalanche]

Gauche the flipper power?ITS TWO FREAKING JUDGE BURSTS, WHAT MORE DO YOU WANT?Seriously the flipper position sure wont matter when its that powerfull anyways

[MassimoV]

Build to the weight limit please.

[Gauche Suede]

Gauche the flipper power?ITS TWO FREAKING JUDGE BURSTS, WHAT MORE DO YOU WANT?Seriously the flipper position sure wont matter when its that powerfull anyways

But with that flipper placement, you haven‘t maxed out the Judge burst‘s potential,srsly just take a look at second sentinel for the best flipper setup.

[Tweedy]

Gauche the flipper power?ITS TWO FREAKING JUDGE BURSTS, WHAT MORE DO YOU WANT?Seriously the flipper position sure wont matter when its that powerfull anyways

Gauche is right, if you place the judge bursts higher up and have the first flipper segment attached to it as the top of the flipper.
And he's building a cruiserweight Massimo

[Avalanche]

FYI im quite happy with the flipper power already.

[Gauche Suede]

FYI im quite happy with the flipper power already.

Can i borrow the bot? i‘ll give you a demo on how different flipper setup affects flipping power.

[Avalanche]

Maybe i should flat out state it.
I will NOT change the flipper position on the bursts for more power.The power is good enough for what I want and more will just make it flip out more.

[Badnik96]

I honestly don't like how there are beater bars on the flippers but whatever.

[Gauche Suede]

Maybe i should flat out state it.
I will NOT change the flipper position on the bursts for more power.The power is good enough for what I want and more will just make it flip out more.

DUDE I JUST WANNA BORROW YOUR BOT SO THAT I CAN SHOW YOU HOW FLIPPER POSITION AFFECTS FLIPPING POWER. IF YOU DON'T WANNA CHANGE IT, THEN IT'S YOUR CALL.
(caps is needed)
(btw, to fix the flip out problem, just put a back stabilizer on the bot)

[MassimoV]

Make your version and take it to the challenge board you 2. Anyways I do have to say I sorta like the bot despite the flaws.

[SKBT]

suede, chill out bro...

Av, if i was you i'd loose the beater bar "8" on the front and switch to a bunch of shell panels or something to get it under 600kg. also the long wedge out the front looks kinda bad and ruins the flow of the bot. i'd switch to to three metal hinge/small wedges across the front.

[Gauche Suede]

suede, chill out bro...

Av, if i was you i'd loose the beater bar "8" on the front and switch to a bunch of shell panels or something to get it under 600kg. also the long wedge out the front looks kinda bad and ruins the flow of the bot. i'd switch to to three metal hinge/small wedges across the front.

i just wanna give him some advice which will let him lose a bit of weight and increase flipping power, and all he says is:

Maybe i should flat out state it.
I will NOT change the flipper position on the bursts for more power.The power is good enough for what I want and more will just make it flip out more.

btw, he only needs to remove  three beater bars and the bot will be a CW.