Author Topic: Ianh05's DSL showcase. (Read 7533 times)

ianh05 · « **Reply #40 on:** August 16, 2009, 01:39:17 AM »

those bars are also weapons btw, so if the razors come off they come into play :P

The Ounce · « **Reply #41 on:** August 16, 2009, 01:45:37 AM »

I am aware of that... :P

life robot arena2 · « **Reply #42 on:** August 16, 2009, 02:26:18 AM »

My entry is a cube. so it may be to high. and it will get trashed.

Somebody · « **Reply #43 on:** August 16, 2009, 08:26:05 AM »

How stable is that?

ianh05 · « **Reply #44 on:** August 16, 2009, 08:36:31 AM »

very stable :D

ianh05 · « **Reply #45 on:** July 10, 2010, 12:26:04 AM »

built a new dsl LW today :) it's a Wammer with flail razors so on impact when the bot goes over it the razors also go up and possibly hit under the other bot.

2 ants, titanium 3, npc fast drive.

Pwnator · « **Reply #46 on:** July 10, 2010, 12:32:03 AM »

NPC+Vlads would probably be better for this due to higher HP, but I'm not sure if it's just as fast as NPCF+Shinies.

It's quite a cool design, but you should try to find another setup so it's invertible. :D

Sparkey98 · « **Reply #47 on:** July 10, 2010, 12:58:16 AM »

I would say try to raise the NPCs an use vlads.

Would that be correct, Mr PWN?

JoeBlo · « **Reply #48 on:** July 10, 2010, 01:01:03 AM »

that could work but it would still get stuck on its face

the top panel + tooth needs to go for invertiblity

Pwnator · « **Reply #49 on:** July 10, 2010, 01:11:19 AM »

Quote from: Sparkey98 on July 10, 2010, 12:58:16 AM

I would say try to raise the NPCs an use vlads.

Would that be correct, Mr PWN?

Depends, really. If I'm right, I think it's using an axle wedge. Drive height doesn't matter much when it comes to axle wedges.

But it's still nice advice. :P

Sparkey98 · « **Reply #50 on:** July 10, 2010, 01:21:06 AM »

Man why does my d key keep doing that, I practically have to hammer the thing.

Anyway, I'm trying to think of a way to offset the front to it's can't get stuck.

Stagfish · « **Reply #51 on:** July 10, 2010, 01:29:30 AM »

Maybe put metal hinge wedges?

Sparkey98 · « **Reply #52 on:** July 10, 2010, 01:34:49 AM »

All I can think of is an angle Iron pointing up from the bottom just jutting out so it won't balance

ianh05 · « **Reply #53 on:** July 10, 2010, 01:44:28 AM »

i really wanted the top protection so it does OK against hammers, i need a rear stabilizer so it doesn't flip on impact then it should be fine. I'm hoping the wedge will be good enough to not have to worry about making it invertible.

ianh05 · « **Reply #54 on:** July 11, 2010, 12:19:43 AM »

Updated my flail wammer:

is more stable, has side protection and is now invertible.

Pwnator · « **Reply #55 on:** July 11, 2010, 12:22:05 AM »

<3

An aluminum sheet on a metal hinge might be better for this. :D

Badnik96 · « **Reply #56 on:** July 11, 2010, 12:31:41 AM »

Cool. Now if only you had entered BBEANS 6...

JoeBlo · « **Reply #57 on:** July 11, 2010, 12:34:32 AM »

awesome

have you seen Mike's Inertia (flail) Rammer ?

ianh05 · « **Reply #58 on:** July 11, 2010, 12:43:35 AM »

yeah I've seen reactive :) and badnik i would have entered something better like the face spinner i made a little while back (still in this showcase) but lost it when i had to reformat my computer.

Doomkiller · « **Reply #59 on:** July 11, 2010, 12:50:16 AM »

*looks at bots*

*drops sultanas*

Well that worked. Anyway nice rammer. Good to see you building again ian